We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hello,
I am trying to make GPIO P0.07 to high, in my nrf5340 Audio DK. Externally I am connecting an LED between P0.07 and GND. But it not showing any voltage between them...
I have the nRF Hw v1, and it seems like I did something wrong with a Fw:
nRF is recognizable by a computer as the COM3/4/5 device:
And it is accessible with the nRF...
Hi,
I want to know how to find the pack of nRF5 SDK.
Because the previous URL has expired. (http://developer.nordicsemi.com/nRF51_SDK/pieces/nRF_DeviceFamilyPack/ )
Hi Nordic
In the documentation of Zigbee sample of nrf Connect SDK, it said:
>>
Support for Zigbee R22 has been deprecated in nRF Connect SDK v2.8.0 and it will be...
Hi Community
Greetings, I bought nrf9151 DK module looking at the features, power consumption & size but the fact that NB IOT has a communication rate of 15mins once in...
Greetings,
We have a PCB with nrf52 and nrf91 on it.
We have nrf9160 firmware with MCUBoot. The chip boots into mcuboot dfu mode when a certain pin is set to high during...
Hi all,
We are running v2.4.0 SLM in nRF-9160 as pure modem, communicating with our external MCU. And we need to send a MODBUS-TCP write request command about each 10 seconds...
Hello.
Thank you very much for releasing nRF Connect SDK v3.0.0-preview1.
I quickly tried the sample program, and while the build was successful, I encountered an issue...
Hi everybody
I'm trying to modify the Zephyr serial LTE modem example so that CMUX can be controlled using another communication interface, specifically I'm imagining...
Our application is designed to remain connected to the network - sending data every 10 minutes or so. We've customised the asset tracker v2 application, as this provides the...
NCS v2.6.0, devices based on nRF52840 (Fanstel BT840)
The project is a star network in which the Central is housed in a steel enclosure with a patch antenna perhaps 1cm...
I've been working on a peripheral wich accepts Just Works pairing requests and I'm completed at all points but the pairing itself. The device advertisises and connects successfully...
Hi Support Team
There are two questions about the KNX IoT over Thread Sever/gateway and Matter over Thread gateway.
1) Customer wants to develop a product support KNX...
For "BLE Central" sample:
I get the same problem when I want to get the BLE devices' name
the "BLE Central" can only get 31-Bytes adv data in "device_found()" callback...
Hi,
Currently I use a custom linker section for my code.
.my_code_section : { PROVIDE(__my_code_section_start = .); KEEP(*(.my_code_section)) PROVIDE(__my_code_section_end...
