But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi guys,
I have a setup to receive the microphone data from the Thingy 52 on an nrf52840 evaluation board. Currently I recive the 131 audio packages ADPCM encodet. In the...
Hello.
There is nRF52840 and nRF9160 on nRF9160 DK.
here are codes on this two chips:
nRF52840: 1:SoftDevice. 2: BLE APP
nRF9160: 1: Modem & GPS firmware. 2: Bootloader...
Looking at PM_EVT_CONN_SEC_FAILED parameters, i.e.,
re: nRF5 SDK v16.0.0, nRF58233, S113
Looking at the definition for pm_sec_error_code_t: “Possible values are defined...
Hi All,
I've had a product (RunScribe) in the market for some time, running on the nRF52832. This was built on the SDK13.1 / and the S332 v4.0.2 SD. All using Keil. As I...
Hello!
I'm planning to start a project with the nrf52832 chip, I mainly choose this product, because of the low power consumptions and ble.
I would like to start my development...
Hi I am using ncs version 1.5.0 and dk version 1.0.0
I just want to try a simple ping test.Is there any at command are sample code is available to check the network connection...
hello i am using nrf52840 with our customised board with sdk version 15.2 i am trying to achieve maximum distance using coded phy with nrf long range demo as my base i have...
Hello. I tried to run ble_peripheral/ble_app_uart example from the newest SDK (17.2) on my ebyte e73 with nRF52833 onboard, but without success. I used softdevice S140 (tried...
HI,
My application needs to send the data from PC(server) to Nrf52840(client) . The length and type of the data are 2758 bytes and char data type, actually data has been...
Hello !
I allow me to contact to you because I don't go through a building issue.
I'm using SEGGER Embedded studio for ARM V5.40c. My target is N52832. It is not the...
Hi,
I'm working on a nRF52832 project with adc and ble function involved. An external RTC is also included, communicating with MCU via I2C. Everything goes well until I...
Please help to tell the meaning of the "built code" after the NRF51822-QFAA-R7y
There is mention "(H0) of built code. Is there any functional / firmware / hardware difference...
I'm using the latest SDK (1.5.0) on a Windows 10 platform.
I want to add I2C support to the BLE sample program peripheral_uart.
I fumbled my way through https://devzone...
