But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
*** SOLVED PARTIALLY ***
Hello again,
I solved my problem partially, the part that reads accelerometer value and transmit BLE advertising data as beacon works fine.
...
Hi,
I want to use a MPU6050 sensor with my nrf52832 board.
I connected the SDA and SCL pins of my sensor board with the pins P0.26 and P0.27 of my nrf52832 board, respectively...
Hello. I'm working with multilink example and I've got some problem. I want to send data to specific peer device, but after restart central or one of the peer, they reconnects...
Hi. I have a problem with Segger Embedded Studio. I always get more than 100% of RAM usage when building project on SES, even if examples projects from SDK . Anyone know what...
Hello, I have the following question. I'm trying to program my firmware via DFU Bootloader and nRF Connect (smartphone). That works perfectly with the test board SparkFun...
Hi,
I am using the two units talking with each other for the BLE uart.
One is running with the example ble_app_uart_c_central. The other is running with the ble_app_uart_peripheral...
Hi, After updating my nrfConnect to 3.6.1, I had issues using my J-link being unrecognized in the programmer app. The J-link I'm using is part of a Silicon Labs Dev Kit, checking...
Hi, I was wondering if there are any problems with connecting VDD to an external power supply when using nrf52840 in the high voltage mode? I would like to connect VDDH to...
Dears,
1.I want to know when working at USB CDC mode, what's the phy rate could be supported? And what's real rate is it？
2.Could customer customized their private protocol...
Hi,
I've read that highly secured IoT devices have a hardware root of trust. One very important feature of it is a private identity keys to prove identities for mutual authentication...
Hi,
I noticed at least using pwr_mgmt we are calling two times nrf_pwr_mgmt_run for every interrupts ! All interrupt seems to be triggered twice ! Or wakes from idle state...
HI Nordic
I currently have a 2 separate projects, that i'm trying to merge.
- Production test tool with RTT CLI interface on nRF52840 (Here I use JLink.exe -device NRF52840_XXAA...
Hi Nordic teams,
I'm developing the function of Mesh DFU. I've test the nrfutil tool locate on https://github.com/NordicSemiconductor/pc-nrfutil/tree/mesh_dfu , and it works...
Hi All,
I have designed one device using nRF52840 MCU and software SDK nRF5_SDK_for_Thread_and_Zigbee_v3.0.0_d310e71.
From Software end all features are implement and...
Hi Sir,
As check nwp_024_v1.6.pdf, it only shows the tape real information w/ below series.
nRF24
nRF51
nRF52
nRF8000
nRF9160
I don't find the information for...
