first,PCA10005 can't load sofeware hex that after s110 7.0.0 hex(include 7.0.0),and gostudio note that the given hex file can not open successfully.
second,the PCA10005...
Hello! I'm using sdk8 and s110. I want my peripheral device to send data to the central. I doing following steps:
1. initialize service:
void services_init(void)
{...
I am glad that I have successfully used the library from www.libstock.com/.../nordic-semi-nrf24l01-example in a pair of PIC18F45k50 devices. One is acting as a Tx and another...
Hello.
I have had a search but can not find anything so sorry if this has been covered before.
Our company has developed a consumer product using the nRF51822-QFAA-R7...
Hi every one !
I am trying to get working a code that it was working "Ok" 2 years ago.
Currently, I cannot get communication between both breakout boards.
To simplify...
I'm trying to solve an intermittent problem when using the nRF51422 UART with CMSIS-RTOS (RTX) and MDK Networking library (V6.2) (TCP/IP stack).
My questions relate to...
Hello,
I am using SDK 15.3 for the development. During the upgrade process I wanted to send the hardware version when requested by the host.
I have made the changes...
I want to use P0.10 of NRF52810 as GPIO. I have added CFLAGS += -DCONFIG_NFCT_PINS_AS_GPIOS in the make file. But still its not working. I am using Nrf 52810 , SDK 15.2.0...
Hello,
I recently decided to upgrade an Arduino project to you nice and well documented products :)
I successfully built and run the example provided here and tried...
Hello! I'm interfacing a sensor with an nRF52840 development board and have run into a few issues:
1) I have a check status function as shown below:
bool ADXL_check_status...
Hello, I'm working on timeslot and RADIO on nRF52840.
I found a sample code which sets 1 to "NRF_RADIO->POWER" to initialize RADIO peripheral.
-----------------------...
Using nRF52832, SDK16, SD132.
I have a (background)bootloader which is derived from dfu "secure_bootloader" example.
When there is nothing to flash bootloader successfully...
The hid keyboard in the routine is buggy. The first problem is that after A device is connected, it is disconnected and other devices cannot be paired. The second problem...
I'm debugging an issue which triggers app_error_fault_handler() and it indicates id=NRF_FAULT_ID_SD_ASSERT, PC=0x18434, and info=0.
This address falls in SD, and how can...
Hello,
I am working on MQTT sample ncs\nrf\samples\nrf9160\mqtt_simple. I am sending data from UART and I2C to the mqtt server. For sending data I am using Workqueue thread...
Hello,
I need to bond a device with its bd_addr using AT_command and unbond device using another AT_command. I am having only DK of nrf52832. So I am trying to bond 2 devices...
Hi,
I'm quiet new with nrf9160.
I try to mix the two sample GPS and MQTT to send my position each time it change to a MQTT broker.
I have create two threads, one for...
Hi, I'm using nRF52 DK to develop and PPK v1.1.1 with Power Profiler app on nRF Connect v3.3.1 to measure current.
1. I see a lot of posts referencing the firmware on the...
Hello.
I have a issue about missing NRF_DRV_SAADC_EVT_DONE event in saadc handler.
setup is 52832, SDK 15.3.0, S332. enable ANT, BLE
for battery, sensor, I use 2 adc...
When I run the BLE peripheral HRS example on the eval board and try to connect with a Samsung XCover3 using the "nRF Connect" app, I got the error 22 (0x16): GATT_CONN_TERMINATE_LOCAL_HOST...
Hi, we are considering using Gazell on the nRF52840 with nRF5 SDK v16. What would be the maximum packet length and the maximum data throughput that we could expect? What would...
