This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello guys,
We are performing BLE Scan with filtering by using the device name as a filter.
We are aware of the following facts:
All the advertising packets will be...
Hello everyone,
I'd like to use 6lowpan over BLE (that's IPSP isn't it?) on the nRF51822, specifically the Micro:Bit. What are the options for doing this?
It appears to...
Hello, I am a student studying zigbee. I want to communicate zigbee with the nRF52840 board, but first I checked the lead on/off of the board where zc_light was uploaded with...
Hello, teams!
Thank you for helping.
Now I'm interested in implementing the direction finding technology by using nRF5340 PDK.
Here are my questions.
1. Is there...
sir/madam i am beginner in nrf52 i want to display time stamp using an in built rtc. i am using that nrf calender in github as reference i am getting the following 4 errore...
Hi,
I have a problem with resume suspended TWIM transmission. My goal is to send | START | ADDR | DATA 1 | DATA 2 | STOP | where DATA 1 and DATA 2 will be send in two separate...
Hello
I am using SDK v17 and nRF52DK board (PCA10040) and testing mpu6050 sensor.
I want to print out the sensor value through the app through ble_app_uart.
Before sending...
HI.
I am trying to connect a laptop BLE and a custom device using HID.
I have to connect multiple devices to my laptop.
I know that the maximum number of connections...
There is an error in projects that utilise RTT for CLI. SDK_CONFIG.H contains the line CLI_RTT_ENABLE. This must be CLI_RTT_ENABLED for the macro NRF_MODULE_ENABLED(CLI_RTT...
I go into MCUBoot mode and I get: MCUboot DFU failed. Error occured when program. Errorcode: CouldNotOpenDevice (0x4) Lowlevel error: Unknown value (ffffff8e) When trying...
Hi all,
I'm evaluating design for a bluetooth + GPS + NB-IoT ultra-low power device
I see the only possibility to get a such module is to design it (I didn't found anything...
Hello,
I'm trying to auto-build my application through Github actions however I'm running into this problem
When I try to run this locally it works perfectly fine however...
Dear All, I am trying to measure the current consumption for an application I am developing on the nRF52833 DK. The code that I am running is the following: Based on the product...
Dear All, I would like to configure a device to go to the System ON, no RAM retention, wake on RTC (running from LFRC clock) Sleep mode, in order to be able to use the RTC...
