We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi!
I have old code written in nRF51 enviorment with SDK nRF5_SDK_12.0.0.
I've successfully flashed the softDevice (s130_nrf51_2.0.1_softdevice.hex).
No error occurs...
hi, I am fresher starting my carrier in ASIC i am learning about UART where i come across with the word "DEADBEEF" in the coding please help me with where it is used and how...
Hi We've been using SDK12.1 with softdevice 3.1.0 on a NRF52832 for some time now. Now we want to upgrade our SDK to 15.2 with softdevice 6.1.0. We've converted the application...
Hi all,
I am working on nRF52840, nRF5_SDK_15.2.0, pca10056,usbd_cdc_acm
I can now communicate nrf52840 with PC,However, I failed to connect nrf52840 to android, Android...
Dear Team,
Greetings !!!
Device - nRF52832 Softdevice - s132_nrf52_6.0.0 IDE - segger embedded studio Bootloader - secure bootloader
In our current application, We are...
Hi,
We have build complex application based on Nordic SDK. Right now we are thinking about moving to Zephyr OS. I was wondering if there is any tutorial/tips I can find...
Hi, I'm using nrf52832 development board. In which i have flashed hci_uart example code of zephyr (latest code taken from https://github.com/zephyrproject-rtos/zephyr ) which...
Hello,
Our product is configured to use 3 total GPIOTE channels –– 2 sensors configured for "high accuracy" GPIOTE events, each around 10Hz refresh rate, and 1 using "low...
Current consumption during k_cpu_idle() after GPIO interrupt does not take the same value. Why does this happen? Any idea? Thank you for reading this post in advance.
<Environment...
hi all, i'm using uart with easyDMA, and i'm disabling and enabling it back on my code. before disabling the uart TX and RX works fine. after disable&enable i get wrong data...
Hello,
as part of the development that will soon be in production, I would need to be able to authorize or not the pairing according to an internal state of my device. ...
The memory returned by the pointer returned from cJSON_PrintUnformatted() in below file must be freed.
https://github.com/NordicPlayground/fw-nrfconnect-nrf/blob/master...
I m analysing application source code searching for implementation of INDENTIFY.
The problem is that application has hundrets of classes and it is very complex so it is...
I am developing a product and there is this situation. My custom board doesn't have UART so I will have to communicate over a Virtual Serial COM Port.
I have a desktop app...
Hi
We want to open L2CAP channel to stream data between nRF52840 and iOS, We cant use OTS example since there is no OTS support from Apple core bluetooth framework.
So...
