Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
Hi,
I am developing an application using the nRF52840 as NCP with a raspberry pi as the primary processor, using wpantund. I have 3 devices (3 raspberry, each with its own...
In most of the examples the FIRST_CONN_PARAMS_UPDATE_DELAY define is set to something like 5000ms. Is there a reason it needs to be that long? I would like to switch to a...
Hi,
My question is quite easy. I need to use 36 or 38 (maybe something else frequency as well) kHz clock in our device. How it is possible or is this possible at all ? I...
Hello All
Since 3 days now, I am trying to program my third party beacon board PTR9048 with the PCA10028. I'm pretty sure, that I connected it correctly, because I can...
Can the
sd_ble_opt_set
function be used to set a default channel map in the central role prior to any connection requests to advertising peripherals being...
Hello,
I am using nRF52840 with nRF5_SDK_15.0.0_a53641a.
I am looking at the QSPI example which I have slightly modified so that after the write of 256 bytes, it enters...
Hello I just got nrf52dk board, and have issues with dfu mode of MCU, after power on board is dead no any lights, no USB connection. After pushing reset and power on, MCU...
Hello,
I am implementing an application, where I want to connect three NUS peripherals to one NUS client. As a beginning point, I started with the supplied examples from...
I have ported the keyboard example code and integrated it with another set of services. However I don't see the device responding to an LL_ENC_REQ. I'm not sure what I can...
This probably falls under the category of BLE Basics, but I'm a bit slow and need some help. Here's my scenario:
I'm building a very simple BLE Peripheral that provides...
I'm currently using nrf8001 to send data to my phone. To save power from the peripheral device, I wanted to change the connection parameters.
I set the min and max connection...
Hi, I'm using nRF52832 with my external board.
I'm recently working ble uart example.
I control motions with tx message such as LED, motor and so on.
Now, I want to...
Hi,
I need to set a client back to the state, when its flash was erased and programed, so if I understand this correctly, the provisioning data has to be erased.
How could...
I've been developing on the PCA10028 development kit with print statements working fine (though at the moment it seems only SEGGER_RTT print statements are working and not...
Hello,
I am getting an error message while I was compiling the "ble_nfc_pairing_reference" example. How can I obtain this " micro_ecc_lib_nrf52.a" file ?
Fatal Error...
