At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Problem description :
When using 'Just works' pairing with LESC key exchange peer_manager doesn't allocate buffer for peer public key and doesn't pass own public key to...
Hello,
I want to know what is the correct way to use GPIOTE while my softdevice is running.
I have referred the example of pin_change_interrupt that is provided with SDK12...
I am trying to start scanning for devices.
I have changed from the example (ble_app_mulitlink_central_s130_pca10028) only
clock source to NRF_CLOCK_LFCLKSRC_SYNTH_250_PPM...
Hi,
I want to know that how if we have Beacon on one side and Development kit on another side so it is possible to communicate them if they are using different services...
I'm using nRF SDK and trying to write firmware to my prototype device. However, nRF SDK doesn't detect my prototype device. I checked the power supply to my prototype device...
Hi,
I am testing example from sdk, 12.2.0, ble_app_uart, nrf52832
And i frequently get a strange behaviour where i don't get a response. And the connection is terminated...
Hello,
I'm trying to set my device on DFU mode by an android mobile application without success.
I'm working with nrf51822, sdk10, softdevice 8.0.
I subcribe to the...
Hi.
I'm using PCA10028, SDK12.2.0, S130 as central.
As I know "sd_ble_gap_tx_power_set" function let me set Advertising Tx power.
How can I set Tx power if i want to...
Hello,
I am going my project with NRG51822 in SDK 11. I build a android app that can connect to my device and access vendor specific service.
My device dedicates one...
Hi, All,
I'm testing multi-connection central function.
And I am struggled in getting relation of address.
AFSK, there are several types of address in BLE.
I found...
Hi.
I'm using nRF51822AC, SDK12.2.0, S130 as central.
After "sd_ble_gap_connect" function, how can I stop this function before connection?
I hope your reply.
Hello,
Is there a way to temporarily disable bonding and just allow any connection? I want to generally use bonding, but there are certain corner cases where I need to...
Hello,
I want to use the FDS libraries in order to store some data into nrf52's flash in my application and I have a bootloader to allow secure dfu by ble.
I manage...
I'm struggling with current consumption. I need my device to completely sleep and leave only the RTC on when the ext power is off (run on battery). After making sure my RTC...
