Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack. ...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
I tried to run s130 example.
For using with pca 10005 on nrf6310 I changed settings like following.
In symbol set from PCA10001 to PCA10005.
In board_config...
I would like to ask you some questions on nRF51822 Hardware:
From nRF51822 datasheet, a 16M or 32M external clock is needed, now if we have one 26M TCXO is available...
Hi
Maybe you can help me.
I'm trying to get Device Manager to work, but I'm having several problems. Although the Device Manager is being correctly initialized and the...
Hi, I am developing a project under Eclipse Kepler & Mac OS X;
The project
When i debug, and set a breakpoint in the main.c, I got this message:
Then after Steping...
hi, i'm new in nrf module, i use nrf51822, i'm totly confuse what voltage that i should apply on DCC pin? if i want use internal dc/dc than what the voltage and if i use LDO...
after setting BLE_GAP_CONN_SEC_MODE_SET_ENC_NO_MITM, I getting BLE_GAP_EVT_SEC_INFO_REQUEST event,
I am using same code as the sample:
case BLE_GAP_EVT_SEC_INFO_REQUEST...
Hi
I am using v6.0.0 softdevice S110 and SDK 5.1.0
In nrf_soc.h the function sd_temp_get() is defined.
The comments there say ..
"p_temp Result of temperature measurement...
Hi,
I use ble_s110_serialization sample code.
I try to notification many 20bytes(total 5KBytes) to my phone, I add some code in ble_app_hrs.
I follow this link to...
I used nRF_Demo_Utility ios app and WFConnector.framework in a sample testing app im building. And when I tried to archive it using xcode it invalidates it with a error message...
Hello,
I’m porting the hids_keyboard demo to work with the nrf51422 dev board. I just changed the #defines for the board in project settings, as well as the pin assignments...
Is there a way to change the scan interval while scanning is on?
I can stop scanning, set a different interval value and start again but that is not my intention, it wastes...
We have some nRF51 beacons kits and we want to connect some external peripherals using the available GPIO pins.
Does any one have an idea on how to solder some pin headers...
I'm trying to implement the ability to change the beacon properties (UUID, Major, Minor) using NRF Beacon Android app. My project is based on s110_nrf51822_7.0.0 (ble_app_beacon...
I'm working with the nRF51822, using the S110 soft device.
My application includes some measurement functions that are timing critical. Ideally, the code would be atomic...
Hi,
Can I use the J-Link Edu programmer to flash the nrf51822? Right now I'm using the J-Link LITE CortexM that I get from the development kit to flash the firmware into...