This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
When I program an interrupt, the NRF52840 requires 250uA extra. I read something about the sense interrupt, but I cannot find any working example. How should I implement an...
Hi,
I am working with Thingy53 using the ESB (Enhanced ShockBurst) library. I have my basic app running with multi-point comms and power control. This was done without using...
Hello,
We have a product which is a custom nRF52832 board, nRF5 SDK (didn't have time to upgrade to nRF Connect SDK), s132, BLE.
We used to call delete_bonds() function...
I‘m tring to run nRF5340 Audio applications with two nRF5340 Audio boards, following at: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/2.6.0/nrf/applications/nrf5340_audio...
I'm using the async API for UART and I have noticed that, shortly after initialisation, I receive a single character with the UART_RX_READY event. This character is 0xff ...
Dear all,
I kindly ask you what is such warning that arise in building the configuration for the NCS example, please point me to better understand why arise and the related...
I now have a 52833 board, my question is what is the difference between it and 52832?
Are they very different?
Which protocol stack does it use?
thank you
Hi
I can't find any info regarding a cut off feature for the nPM1300 if the battery voltage is to low.
we are using a battery with PMC but that is meant as last resort...
I am using nRF52840 boards. I have one query.
I understand from your documentation that MPSL schedules the Radio driver to access the Radio. And BT ticker is for time slots...
Hi
I have flashed the unit with the Vysor flash file at Vysor Dongle · koush/vysor.io Wiki · GitHub The unit is now dead and has not recovered so I am returning to amazon...
I was planning on writing firmware for the nRF52840 chip (AKA System Controller) on the NRF9160 DK. Primarily it will use BLE and serial communications over some of the pins...
Hi, I am using nRF52840 and nRF Connect SDK V2.6.0
I want to send 7000 bytes of data using USB at a time. Now I am able to send only 1024 bytes at a time. I modified USB...
I'm using the nRF52+SDK11.0.0+s132. I'm developing a system that streams BLE notifications to an Android app at ~53kbps (40B/6ms). I have the connection intervals set to 7...
Hi,
I have a system I am redesigning to use the npm1300.
It has a rechargeable battery, about 3-4 weeks per charge, connected to an nrf9160.
The current system...
Hello,
I had to build the https_client sample again to compare some behaviors on my application and as I flash it to nRF9160 I am having a cyclical error as below:
...
