Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
Hi,
I would like to ask a few things about Channel Sounding (CS):
Is there any recommendation which method (IFFT, PBR, RTT) should be used for reading the results...
Hi
I`m working with an nRF52833.
I've observed that when the module enters DFU mode, the Bluetooth advertising name seems to be limited to around 22 characters.
If I...
I am trying to run the WiFi Station sample, unchanged on a nrf7002DK, but receive the following error: "wifi_supplicant: Failed to add iface wlan0" Complete output as follows...
I’m currently experiencing an issue while trying to install the Toolchain Manager application from nRF Connect for Desktop (v5.2.0) on Windows 11.
Every time I attempt to...
Setup
Hardware: Nordic nRF7002DK as Wi-Fi STA (client) .
AP & Receiver: a Linux PC creates a Wi-Fi Hotspot/SoftAP (NetworkManager/hostapd) and simultaneously runs...
I’m having an issue using QSPI flash with NRF Connect SDK 3.1.1. I have two PCB versions with nRF52840 MCUs — one uses the W25Q128JVEM chip and the other uses the W25Q128JVPIQ...
I want to connect a W25Q01JVZEIM (128MB) NOR Flash ROM to SPI3 of the nRF52833 and implement USB MSC functionality. However, the build fails. It seems the overlay description...
I'm communicating to the nPM1300 eval kit over I2C from an nRf52833 DK (running a fuel gauge application). This works well until I connect PowerUp (through USB) and enable...
Hello to everyone!
I bought nRF54L15-DK for Matter Over Thread developing and prototyping.
Before nRF54L15 I tried ESP32C6 XIAO + Arduino IDE and it worked but it was...
Hey, I have an nrf52840, with lis2dh sensor.
I configured the sensor using the devicetree using the following code
and I change the sensetivity and some other register...
Hi all
I am very new to BLE development and I hope that this question was not asked before in another way.
Is this example also available in nRFConnect with another name...
I'm using an nRF52840 microcontroller on an electronic board to read from and write to an S25FL064 flash memory chip. I'm currently using the nRF5 SDK . Before I could read...
I am trying out the Nordic Bluetooth ESL sample example code from the link [ Getting started with bluetooth-esl-and-periodic-advertising-with-responses-pawr ]
Downloaded...
I understand from many posts that the DTS file is ignored when in multi-image (mcuboot enabled) I need to change the partitions to reduce the bootloader from 48K to 32K &...
