Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
This question relates to the unsatisfying reponse to ticket 283390.
The technology of the processor is not important. Arm Cortex processors are as fine as several others...
I am having trouble setting up a GPIO pin that will toggle when the radio is active on the network core. I have tried adding the code in bluetooth.c from the ppi_trace sample...
Hi everyone!
I am developing a board using a nrf52 as a BLE interface for an arduino. My idea in the future is update the firmware of the Nrf52 with OTA. But i wanna do...
Hello everyone. I am trying to set up a BLE central-peripheral network using nrf52840 based on NUS service. I need up to more than 10 peripherals which is customized board...
Hello there,
I'm trying to make a transceiver simulation on nRF24L01+ using Simulink. The block diagram provided in the documentation/datasheet was not clear enough for...
To create the prototype of a computer, which follows a non-von-Neumann-architecture, I am looking for an "Building Kit", which allows non-standard connections between computer...
Hi,
I'm trying to build my own "auto sleep" mechanism based on timers.
This is my code:
The timer works as expected, but when the soft_sleep function is reached, the...
We have a device that we are trying to implement an encrypted data transfer on. We wanted to lock down all the characteristics until we write a passkey on our security characteristic...
Hi there, I am trying to change the transmission power of the NRF5340 devices (for IEEE 802.15.4 radio) with Contiki-NG. With some other hardware (sky motes) that is based...
Hi,
Using Power Profiler v3.3.0 with PPK2 on Chrome on MacOS.
The screenshot action results in a chopped image. See the top part is missing?
When I remove (by commenting...
Hi,
I'm trying to interface to a third-party 802.15.4 RF chip using an nRF52833, where the received packets from the remote device have enabled AES-CTR encryption.
I started...
Hello everyone,
I am looking at the init structure of the NRF52832's RTC and I cannot find any explanation on the "reliable" variable.
I can see its usage in the driver...
Hi,
I have an application for the nRF9160 where I want to use mcuboot and of course signing, but I get the following message while building, that my key file is invalid...
Hello, I'm trying to use the nRF52DK development kit as a Bluetooth sniffer. after following your "nRF_Sniffer_UG_v2.2.pdf" guide, all I see in Wireshark are advertising messages...
Hello, I want to know how I can print console messages out over the COM ports that the Thingy:91 exposes using the nRF Connect SDK. I'm able to see the com ports but I'm unable...
