Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
I've tried sending ASCII "Hello world" over SPI with various data rates. Somehow clock signal given by SPI is not continuous. This discontinuouty differs with clock frequency...
Hi everyone,
I want to integrate the Queue module into my firmware. I found three functions for writting elements in the queue
1. nrf_queue_push
2. nrf_queue_in
3...
Hello,
I am migrating my project from GPS driver to GNSS interface. I am facing a few problems when I am using GNSS interface.
1. GPS driver can generate simulation data...
Hello,
I am new to the NRF World and try to explore some Ble examples. Unfortunately I can't get the BLE_Blinky Example working. The Flashing works without problems, and...
Hello,
I developed a script which has a 40Hz timer which repeatedly starts the NRF52840's SAADC in continuous mode (with a 40kHz rate) which is supposed to fill a revolving...
Our codebase is configured to use West to manage our code repository as well as the NCS repositories. We use the 'name-whitelist' option in our `west.yml` to only import the...
Hi
I am writing the firmware of a wearable device, based on nRF52832, which must support OTA DFU. I am using the peer_manager to manage paring and bonding, and the FDS library...
I'm trying to use the lpuart sample for a project, but everytime I try to flash I get a zephyr fatal error 4. I dont know what I doing wrong can anyone help me?
error: ...
Hello,
OS: Windows 10
SW Version: nRF Connect 3.9.0, Programmer v2.0.0
Nothing has changed hardware-wise. Still using a Segger J-Link to try to complete this task. I...
Hi,
I have an application where I use nrfx_saadc for getting some samples and I also run the st7735 driver, modified to use nrfx_spim instead nrf_drv.
For the nrfx_saadc...
Hi.
I'm currently evaluating all the DFU options available for nRF5340 using v1.7.0. One of those options is the mcuboot serial boot option.
During my mcuboot...
I am using nrf52832 with provisioner example from mesh v4.2.0. I want to know if the servers i configured using the provisioner is able to detect when one of these servers...
We are using NRF52840PDK for development using NRF Connect SDK. We are facing an unusual behavior while using PDK. The development environment is Windows 10 and SES5.60 installed...
Hi,
we are trying to send data (a packet of 54 bytes) at 100Hz but our data is not always transmitting regularly.
Much of the time the TX is perfect but every so often...
Hi,
If i need to call zephyr driver API clock_control_off( ) present in zephyr\include\drivers\clock_control.h on LFCLK. How can I do it,.? As an example, to populate...
