But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
I am working with the chip ISP4520 which combine Nordik NRF52832 and LORA semtech. I use nORDIC sdk 14. I burn the FW to the chip using Nordic development kit connected by...
Hi,
I tried a light-switch example from SDK for mesh ver 4.1.0 on two nRF52840 DKs(first board with client and the second with server). I configured them with nRF Mesh app...
Hi,
I have an unkown problem in my nrf52 application. It happens rarely, so I have no idea where to look at the moment. The only thing I know is that the WDT works and resets...
I have browsed through the forum and i couldn't find a similar question, so here I ask :
I have an application running a modified example of the Mesh Client & Server merged...
Hello there,
I'm trying to use my NRF51822 custom board as spi slave with BLE that sending whatever received from the master. I'm using MSP430FR5994 as the master.
I...
Dear Nordic,
I'm new in Bluetooth mesh and Nordic SoC.
I want to develop network of measure devices connected to each other using Bluetooth mesh. All devices need to report...
Hi all,
I installed this app on my nrf52832 DK and it works great. I'm totally newbie with Nordic and its hardware so i can't figure out how to adjust this code so the app...
Hello,
we are upgrading our application firmware to the v1.3.0 of nrf-sdk. We have now encountered a problem in which the build process just freezes/stops without exiting...
I try to build and run a "blinky" example for nRF52840 DK and nRF5340 PDK. And in the case of nRF52840 DK everything works properly. I connected to the boards and saw UART...
Hi! Some prerequisite info:
We are using nrf52840 boards as our peripherals
We are using v16.0.0 SDK
We are using the s113 SoftDevice, more specifically s113_nrf52_7...
Hi,
I have a topology which has 20 to 50 nodes and these nodes should send a data packet of approximately 20 bytes at 50 Hz to a single gateway node. Is BLE mesh suitable...
hello nordic
i have been working with nrff52832 with the SDK16.0 (also working with s132 if it matters)
it is a real head braking to deal with your never ending sdk_config...
Hi team,
Do we have any evaluation on the nRF Connect SDK size if customer wants to run on nRF9160? Customer wants to evaluate their Flash/ RAM buffer for APP.
Thanks...
Dear Sirs,
I am trying to use the FDS Storage Library to store 4word = 16 bytes in to flash.. Which seems to be working fine. No errors and the function is shown below...
Hi,
We have custom board based on nRF52833 SoC. We are trying to use SDK_v16.0.0/examples/ble_peripheral/ble_app_uart/pca10100/s140.
Using Segger Embedded studio, program...
