I'm trying to solve an intermittent problem when using the nRF51422 UART with CMSIS-RTOS (RTX) and MDK Networking library (V6.2) (TCP/IP stack).
My questions relate to...
Hi...
When i was working in SDK v6.1.0 i have tried nrfprog.exe to merge and program bootloader, softdevice, application and bootloader_settings file as explained in devzone...
But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi Nordic Support Team,
I am planning to use nRF9160 Customised Board for NB-IOT Application.
I want to make it battery Operated Device.
As i want to know how Communication...
Hello,
I am using SDK 15.3 for the development. During the upgrade process I wanted to send the hardware version when requested by the host.
I have made the changes...
I want to use P0.10 of NRF52810 as GPIO. I have added CFLAGS += -DCONFIG_NFCT_PINS_AS_GPIOS in the make file. But still its not working. I am using Nrf 52810 , SDK 15.2.0...
Hello,
I recently decided to upgrade an Arduino project to you nice and well documented products :)
I successfully built and run the example provided here and tried...
Hello! I'm interfacing a sensor with an nRF52840 development board and have run into a few issues:
1) I have a check status function as shown below:
bool ADXL_check_status...
Hello, I'm working on timeslot and RADIO on nRF52840.
I found a sample code which sets 1 to "NRF_RADIO->POWER" to initialize RADIO peripheral.
-----------------------...
Using nRF52832, SDK16, SD132.
I have a (background)bootloader which is derived from dfu "secure_bootloader" example.
When there is nothing to flash bootloader successfully...
The hid keyboard in the routine is buggy. The first problem is that after A device is connected, it is disconnected and other devices cannot be paired. The second problem...
I'm debugging an issue which triggers app_error_fault_handler() and it indicates id=NRF_FAULT_ID_SD_ASSERT, PC=0x18434, and info=0.
This address falls in SD, and how can...
Hello,
I am working on MQTT sample ncs\nrf\samples\nrf9160\mqtt_simple. I am sending data from UART and I2C to the mqtt server. For sending data I am using Workqueue thread...
Hello,
I need to bond a device with its bd_addr using AT_command and unbond device using another AT_command. I am having only DK of nrf52832. So I am trying to bond 2 devices...
Hi,
I'm quiet new with nrf9160.
I try to mix the two sample GPS and MQTT to send my position each time it change to a MQTT broker.
I have create two threads, one for...
Hi, I'm using nRF52 DK to develop and PPK v1.1.1 with Power Profiler app on nRF Connect v3.3.1 to measure current.
1. I see a lot of posts referencing the firmware on the...
Hello.
I have a issue about missing NRF_DRV_SAADC_EVT_DONE event in saadc handler.
setup is 52832, SDK 15.3.0, S332. enable ANT, BLE
for battery, sensor, I use 2 adc...
When I run the BLE peripheral HRS example on the eval board and try to connect with a Samsung XCover3 using the "nRF Connect" app, I got the error 22 (0x16): GATT_CONN_TERMINATE_LOCAL_HOST...
