I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
Hello,
I have a small test BLE peripheral application with a few functions I can invoke over a UART dialog. With one function, I can print the first peer in the peer manager...
Hi,
I'm using the ble_app_uart example as a starting point for my project. Basically I want to program the nRF52 DK to receive data from another device via UART, store them...
For either the nrf52840 or the nrf52833 which pins are responsible for configuring the serial preference SPI, UART and I2C and how to map them. Are they any software examples...
Hi,
i am working with nRF52840-DK and i want to implement a network with below futures
The node(means nRF52840-SOC) Should work as a listener
1. the listener should...
Hello,
I'm getting started with nRF Connect SDK. I've installed the toolchain and SEGGER through Getting Started App (because for some reason the Toolchain Manager froze...
Good day,
I have done DFU using the secure bootloader example in sdk16 using the nrf connect app. The DFU process completes successfully and the controller runs the new...
Good evening, I'm looking for a Blue Tooth BLE Low Energy for Low Power application.
This application should consume few mA only when the controller will be in TX and so...
Hi,
Could I get clarification on if the USB peripheral is isolated and won't backfeed?
In my product, VDDH & VDD are powered via a DC adapter that can be unplugged while...
Hello,
I continue to deal with Zigbee and I have another question. I use 2 nRF52840 chips. First nRF as a Zigbee Coordinator (CLI in SDK\examples\zigbee\experimental\cli...
Hi Team,
We are planning for use the NRF52832 Module for our development, In that for Secure data storage exchange we are implemented the some of the crypto mechanisms...
Hello,
When operating the Thingy91 in poor network connectivity environments, the call to getaddrinfo will sometimes block and eventually timeout returning a error code...
Hello,
I am using the nRF52840_DevKit and SDK-v16.0.0. I am planning to build and flash a bootloader with NRF_BL_DEBUG_PORT_DISABLE set to 1, which means APPROTECT and...
Hi,
I'm using SES v4.52b, a nRF52832 module (BL652) and nRF5 SDK 16.0.0. I'm trying to build a generic SPI Read and Write functions with the following:
The device I...
Hi there,
I am in the process of developing a custom PCB using the nRF52833 SoC. This board is quite simple, and doesn't use many of the pins of the nRF52833 SoC.
I am...
nRF5_SDK_16.0.0_98a08e2\examples\peripheral\uart. In the SDK 16 ,UART example,why the legacy driver nrf_drv_uart.c is used instead of the sdk recommended nrfx_uart.c.
Secondly...
