After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
Hello,
Softdevice: 7.0.1, SDK: 16.0, Device: nRF52840
In the production, we want to save time programming the devices. So I'm using following command to combine bootloader...
Setup : I am using android-ble-library for my android app. I am using modified blinky example on embedded side. I have tried following implementation on android app:
I...
I have two nrf51822 devices, one running s110, the other s120. The s110 device reads ADC values every 20ms, and if they changed from the last reading it sends a notification...
Hello,
The following define is present in file nrf_sdm.h, SDK 17.0.2:
#define SD_FLASH_SIZE 0x26000
I think it's wrong, it shall be 0x27000. But it's maybe not used...
I am working with a IC that requires SPI clocks to be synchronized (in phase) with its system clock. Currently the IC's clock source is connected to one of the nRF52's GPIO...
problem: in BLE data length negotiation , In the response from slave tx doesnt go above 216 , and rx doesnot go above 54 .
s140
Experimental UDP example - sdk v16.0 (...
Hi.
I'm pretty new with SEGGER Embedded Studio and with nRF9160 dk.
I would to receive time with NTP serveur but I'm lost.
I don't know what to use. if it is better...
Hi, I am working on nrf52840 and I am trying to enable the repeated pairing attempt protection. (PM_RA_PROTECTION) After enabling the module I can see the logs telling me...
Hi All,
I want to create a Thread network with multiple OTBRs, which is based on two nRF52840 run Thread RCP hex provided by Nordic SDK.
I created the thread network by...
Hi there,
I would like to set my dongle into DFU mode from software, I am using the USB-CDC-ACM class, and the softdevice as a central device.
Ideally I would send a...
Hello,
in our project we have a nRF52840DK as central and a nRF52832 chip on a custom board as peripheral. The software on the nRF52840DK is based on the ble_app_uart_c...
Hello
I use mpu6050 and I want to use a 'Complementary Filter' to get the angle of the X, Y, and Z axes.
Applying this filter to the value of mpu6050 seems to reduce...
Dear all,
Greetings!!!
I am using the NRF24LE1E module. I want to pair my device with host using a button. Button is available on device side. Please help me to do it...
now ,nRF52810 's serial port receives bytes.when the bytes sent by peripheral devices are mode then 20 bytes,nRF52810 will die.if the bytes are less than or equal to20 bytes...
Hi, all
(nrf52832 pca10040 s132..)
I'm trying to send / receive data with custom data using gpio ..
My custom device's baudrate is 9600 so I initialize uart like this...
