But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello,
I'm working with an nRF52832, SDK 14.2 and Freertos 8.0.1.
Two tasks are defined, one for led signalling and one where saadc is used to check the battery value...
Hi,
This is actually a follow-up to my previous question here: devzone.nordicsemi.com/.../publish-timeout-handler-of-one-model-called-during-publish-timeout-handler-of-another...
1. I have an nrf9160 module, patched on the customer's own board. 2. I want to connect this board to nrfcloud 3. I read the imei of this nrf9160 module through the software...
Hi, I'm working on NRF52832 ble_upp_multirole_lesc example in SDK15.0.0. When I try to activate its DCDC attribute via NRF_POWER->DCDCEN = POWER_DCDCEN_DCDCEN_Enabled or sd_power_dcdc_mode_set...
Hi Team,
Hope you are doing well, and safe from this pandemic.
I would like to ask that, is there any serialization for zigbee from linux PC?
As we have verified...
Hello,
I noticed in the release notes for nRF Connect SDK v1.2.0 there is a known issue with the nrf_send function as it relates to blocking for several minutes, see below...
Hi,
We have successfully verified "BLE UART and Zigbee Color Dimmer Light Switch Example".
Right now we see there is no support for receiving reports from light bulb example...
Hi,
I recently discovered the platform. I'm trying to modify the examples in order to understand the different ways it works.
My last step was to add a Generic On Off...
Hi , I am compiling the bmdware project (in IAR embedded workbench 8.32.2) and I have errors (particularly Errors while linking assembler, shown below).
I have modified...
Hello,
I am using Segger Embedded Studio version 4.52b and when creating a new project, it automatically creates a segger link script file and sets the linker to 'Segger...
Earlier with SDK 13 in custom advertisement I was able to send 30 bytes under unknown characteristics tab in Nrf connect APP but in SDK 15 I am not. Because the firmware or...
Hi everyone,
I started working on the nRF9160 with a Thingy91. I installed nRF Connect SDK v1.2.0 and i was able to try some sample like GPS or AT_client. However I would...
Hi ,
SDK : 16.0.0.,Mesh V4.0 ,PCA10040
My project requirement is : I need to use 2 dev kits one as a server and one as a client communicating each other on BLE Mesh
...
Hello, I'm setting up a mesh network with low consumption sensors and I'm using the Low power node example. I'm having trouble increasing the number of devices supported by...
Hello,
How can I directly read out the POFCON register value on the Watch Window while debugging?
Where is it actually located in the library(sdk 14.2) source code?...