But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hi,
I try to rotate an image (180) with nrf_gfx_rotation_set(p_lcd, NRF_LCD_ROTATE_180). This only works once, but after, I want to return to the original position by re...
Hello
I am currently trying to get sensor values via SPI communication with mpu9250, a 9-axis sensor.
Although the following settings were made,acceleration,gyro,and...
Hi Sir,
I am going to the same phenomenon as below.
https://devzone.nordicsemi.com/f/nordic-q-a/45554/sdk-15-2-how-to-set-a-value-to-a-hid-feature-report
Can someone...
Eventually we got it working with the Master Control Panel again, but it will not work with our test software. I suspect a Window update change that affected links. Window7...
Hello,
I would like to implement a design using both the ESP32 Wi-Fi as well as the nRF52840 on the same PCB. As they both operate on the same 2.4GHz frequency and the antennas...
Hi,
I have used "write_handler(p_ble_evt->evt.gap_evt.conn_handle, p_rtc_service, p_evt_write->data[0]);" to send data to nrf52832 from mobile but iam able to send 1 byte...
Hello, I have 2 custom service running each with one characteristic. When data is written to the characteristic one (io_controle.c) the write event is triggered twice. The...
Hi,
did anybody find a suitable and cheap enclosure for the nRF51 Dongle? I want to use some of the dongles for initial tests before producing my own boards.
Thanks...
Hello, I have modified the example from the light switch on the mesh SDK and I can send and receive string messages, but the problem is that it doesn't work as expected, because...
I (unfortunately) had to make my own forks of Zephyr and NRF to get around a build issue, and decided to implement a west.yml manifest in my application repository. I made...
A makefile project using SDK 15.0.0 that compiled under GCC 7.2.1 no longer compiles under 7.3.1 with these errors:
../../../../../../external/segger_rtt/SEGGER_RTT_Syscalls_GCC...
Hi
I am trying to run the light_switch example, following the steps provided in this link . I have one Development board and 2 custom boards. It asks for Segger IDs for...
Section '5.2.1.1 Sleep' of the nRF9160 Production Specification v1.0 identifies SLEEP power with no RAM retention. My application will require partial RAM retention during...
Hi
I am trying to start development with Bluetooth Mesh. As per the documentation here , I have installed nRF Command Line Tools. While running the python script "quick_start_demo...
