This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to prototype an application on the nRf52 DK (PCA10040) using the GCC toolchain. I followed all of the tutorial for setting things up and I can build and...
Hi all,
I tried to load the DFU example for nrf51822 from SDK12.3 on the dongle(PCA10000).
softdevice: S130 2.0.1
I followed the tutorial on: devzone.nordicsemi.com...
What I am trying to accomplish is to establish a connection between an iPhone (device 1) and an NRF52 (device 2), then sniff the data sent between them from a third device...
Hello,
I have designed a custom board with NRF52832 IC which controls vibration motors. And I am turing on vibration motor from n-channel mosfet as shown in the image below...
Hello ,
I'm using ble_app_eddystone example and I would like to stop the advertising and TLM when I press button 2. I able to create a correctly inicialization of button...
we validate the example /ble_centeral/ble_app_multilink_central with NRF_SDH_BLE_TOTAL_LINK_COUNT equals 8. Change the number from 8 up to 15, it still work.
but when the...
in a ble_nus_c_evt_handler().
SDK13, nRF52, S132.
I made connect success. When it done, I send command to peripherial to start discovery. When event came
case BLE_NUS_C_EVT_DISCOVERY_COMPLETE...
Hi, when trying to read a register from a chip using the IIC interface,blocking mode:
uint32_t ms5837_cmd_read(uint8_t *data, uint8_t length, uint8_t register_address)...
On a custom board with an nRF52832, I have some LEDs I'm driving from the pins 9 and 10. One or both of these pins are used for the NFC antenna unless you configure them as...
I am trying to understand the whitelist feature by following the HID Key board peripheral example on S140 v5.0.0.-2_aplha on nRF52840 dev kit. I am using iPhone SE with nRF...
Hi all,
I'm trying to return a write response in nRF sdk but so far no success.
Actually I'm still scratching my head to figure out how characteristic write works exactly...
I am trying to build and debug the Mesh v1.0.0 light-switch server example and getting a
cryptic error when launching the debug.
My environment is Segger v3.30 on macOS...
Hello,
I just bought a nRF52832 development kit
infocenter.nordicsemi.com/.../nRF52_DK_User_Guide_v1.2.pdf
The board can pair and data transfter with mobile after i...
With a little research, I came to the probably erroneous conclusion that the "NRF_ERROR_INTERNAL" error I keep getting is likely caused by my not using a twi event handler...
