Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
According to the point above
link text
i bought the thingy but i did'nt think about the jlink ..
you can add me to the advent calendar ;-> for a nRF52 DK because...
I understand that the connection parameters viz. connection interval, connection supervision timeout and slave latency are negotiated between the BLE Central and BLE Peripheral...
We currently have a SPI interface between MSP and the Nordic nRF52840. In the DTM documentation it indicates UART is used to command the tests. Is it possible to do this using...
Hi,
I have 5 nrf52832 and nrf52851 beacon boards. All nRFs working in the beacon mode. They all in the same room. I tring to get a list of the active beacons the module...
Started out with the ble_nus-exmple. Added logging of a sensor to flash, and got it to work in SDK11, even without using the sd_flash*-routines, but writing/erasing directly...
I would like to perform an OTA on the DWM1001 board which has a nrf52832.Where can i get the details an the range that can be achieved with employing ANT.Are there any test...
I am following Tutorial 7 on "Development with GCC and Eclipse" and I am working in the Windows 8.1. I have followed instructions from the tutorial for installing the arm...
hi,
i am using a nRF5240 DK for receiving multiple services and characteristics data from Nordic_thingy_52,to receive and print this data on UART i used sdk 14.2.0's "ble_app_blinkey_c...
Hi there~. I was working on a BLE RC car (BLE peripheral) using Nordic's nRF52832-QFAA MCU , Nordic's UART Service for motor control, and Battery Service (BAS) for battery...
Hello.
The development environment is as follows :
OS : Windows 7 Pro 64bit
IDE : Keil uVision V5.24.1
Python : 2.7
SDK Version : nRF5_SDK_14.0.0
DK : PCA10040...
I want nrf51822 to switch between 2 different advertising timeout. One will set advertising timeout with 20s, another will keep advertising.
Currently, I use following...
I have a server running on my Android phone. I looked at the service UUID encoded in the advert packet using and Wire-shark and confirmed my app is broadcasting packets. ...
I am trying to execute code that broadcasts (uses the Soft Device Ble stack) on target nrf52832 boards connected to the PCA10040.
I am successful uploading a program (that...
