first,PCA10005 can't load sofeware hex that after s110 7.0.0 hex(include 7.0.0),and gostudio note that the given hex file can not open successfully.
second,the PCA10005...
Hello! I'm using sdk8 and s110. I want my peripheral device to send data to the central. I doing following steps:
1. initialize service:
void services_init(void)
{...
I am glad that I have successfully used the library from www.libstock.com/.../nordic-semi-nrf24l01-example in a pair of PIC18F45k50 devices. One is acting as a Tx and another...
Hello.
I have had a search but can not find anything so sorry if this has been covered before.
Our company has developed a consumer product using the nRF51822-QFAA-R7...
Hi every one !
I am trying to get working a code that it was working "Ok" 2 years ago.
Currently, I cannot get communication between both breakout boards.
To simplify...
I'm trying to solve an intermittent problem when using the nRF51422 UART with CMSIS-RTOS (RTX) and MDK Networking library (V6.2) (TCP/IP stack).
My questions relate to...
I am using eclipse as IDE , but when i build ble_app_hrs example it's getting an error ../../../../../../components/ble/ble_advertising/ble_advertising.c:195: undefined reference...
I have a 32u4 Feather but don't get the right support from Adafruit to create my own Profile. I have downloaded Nordic's android app and can see all the characteristics on...
Hi.
I'm trying to enable and disable softdevice repeatedely.
In my code, softdevice is firstly enabled then advertising properly.
After some seconds, softdevice is disabled...
Hi,
I used the ble_peripheral and ble_central example and I send messages from one to the other.
Know I need to do the same with multilink.
I managed to connect ble_multilink_central...
hi dear Engineers!
the questions is it possible to use RX RF reciever to estimate the average BW RF signal input power like I do it in Semtech 433/868 RF SoC to make desicion...
hi, all
my nrf52832 can not run good when download the program into the flash, and can not run good in debug session mode without breakpoint ， but if I add one breakpoint...
Hi,
I am trying to send L2CAP connection reply by using this "sd_ble_l2cap_ch_conn_reply()",but i am unable to see the packet on wireshark. The incoming connection handle...
Hi I note here that it is recommended to apply solder mask to the ground layer beneath the nRF24L01+ exposed die so they don't connect:
devzone.nordicsemi.com/.../
But...
I'm finding a discrepancy with numbers between the nwp_008 whitepaper (quarterwave printed monopole antenna for 2.45ghz) and AppCad values.
I've assumed you can measure...
Hi.
Months ago I loaded the nfc_url_record example and it worked fine.
Later some time I updated the packages, and since then that particular example gives errors.
The...
Hi,
Anyone familiar/experiened in production-test gear for BLE?
Test sets, i.e. LitePoint, Anritsu, USRP, NI?
What's relevant to test, i.e. output power...
Figure 222 of the OP spec states "important: no components in bottom layer". Are you recommending that we keep the bottom side clear under/near the nRF52840? This feels a...
I met some problems in testing ECDH , the project is the example in E:\Source\NRF52832\nRF5_SDK_11.0.0_89a8197\examples\ble_peripheral\ble_app_uart\pca10040\s132\arm5_no_packs...
Hi!
I am using SEGGER Embedded Studio for some of the projects. I do utilize C++ in the projects wherever possible and have found that I cannot make the delete operator...
I am working with nRF24LE1 and I use the Gazzell library. But I need a real time base. I have a chance, because I think Gazzell uses that resource. Is there any way I can...
