Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hello,
I am currently working on a BLE Mesh–based control system and would appreciate guidance on a few architectural and scalability concerns.
System Overview The network...
According to the working principle of a crystal oscillator, the load capacitance is inversely proportional to the resonant frequency of the crystal, that is, the larger the...
Hi,
We are using the NORA-B126-00B module on our custom board, and the first time we flashed it with a simple LED blink example, it worked fine. However, after erasing the...
Hi,
I'm looking at the watchdog behavior in mcuboot during DFU. Here are the watchdog-related configs I've set:
and here are a few things I've noticed:
- Even though...
hello, When I switched from the NCSv3.0.0 version to the NCSv3.2.1 version, I encountered the following compilation issue. How should I eliminate this "Error 1 (Ignored)"...
Background: Our tests on SDK 2.5.0 showed that it was possible to maintain a Bluetooth connection at a distance of approximately 180 meters with the following initial advertising...
i am performing DFU process b/w nrf54l15 and nrf connect mobile_app ( Android ) and i am sniffing the it using nrf54840 soc and the bord is nrf21540dk in Wireshark i know...
Hi,
I am currently working with 2 nrf54L15-DK and a seperate 4 antenna array.
For my tests i run a 2x2 antenna config with preferred peer set to 1 and 4.
I was now...
I just got the board, installed the nRF connect sw. Then installed the J-link, connected the board, power it on and run the quick guide, but it searches and doesn't find anything...
I've been using PPK2 to test our work for maybe around 3 years. it's always been steady and stable and can run for several days without problem. Mostly I'm using the PPK2...
I'm running the nrf5340_audio_dk and using version 2.6.0-rc1. When connecting one NRF5430 as headset to another NRF5340 gateway, running BIS mode everything works fine. But...
Hi,
We've been working on an IoT device that uses an nRF52840 in a pre-approved module from Moko. We are getting ready for a commercial launch in 2026, but I am very confused...
I have noticed that the dts file includes the configuration for arduinio_spi, along with the corresponding pins associated with spi4. However, I am unsure about how to utilize...
The Bluetooth 6.0 Channel Sounding feature supports multi-antenna functionality. The nRF54L15-DK development board is currently single-antenna. Is there any official documentation...
