Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi
After nRF Connect for desktop was upgraded to v3.6.1, programmer application cannot recognize all DK boards, including PCA10040/PCA10056/PCA10090.
It showed the error...
Can I use nRF21 in GPIO mode (not SPI) using the PA/LNA assist feature of the S112 soft device?
Per section 5.3 of the datasheet, it seems I could wire the PDN pin to be...
Hi,
I am learning how to write and read from flash memory on nRF52833 dev board for a BLE application.
I followed the heart rate example as shown in https://devzone.nordicsemi...
I am writing an application for the nRF52DK which uses two additional push buttons besides the 4 already present on the board.
Using GPIOTE the detection of the button press...
I have a working project that uses the NRF_LOG module to send debug outputs over the UART backend. When just using the logging module everything works correctly.
I added...
Hi,
Is it possible to set multiple APNs in nrf9160 and with fallbacks to next APN if one not working?
Suppose if we set 2 APNs at CID=0 and CID =1 positions using AT+CGDCONT...
Hello I am trying to execute the functions of SPIS and thread on nrf52840 Refer to his code to write nrf52840 SPIS: https://devzone.nordicsemi.com/f/nordic-q-a/68854/nrf5340...
Hi,
I am trying to configure the nRF Connect SDK on a Mac running Catalina for the first time and have followed the nRf Connect v3.6.0 - Getting Started Assistant.
I am...
I am new to the Segger Studio and nRF52840 . (However not a Newbie to Microprocessors)
Off the Bat :- Blinky example works fine...
.....however when I try to get the PWM_driver...
Hello, I wanted to know do this chip ( nRF52810) has both tag (beacon) and receiver function? If cannot is there any other Bluetooth chip suggestion? My main idea is to use...
I am new to Arm and Nordic devices and I am trying to port the Thingy52 firmware to SES so we can add some additional sensors.
I have got the Thingy52 firmware to compile...
Hi Nordic Community,
I follow the below link to create an openthread border router. I successfully send sensor data on things.io.
https://infocenter.nordicsemi.com/index...
I've implemented the nRF52840 QIAA var5 reference design in hardware and it works well. For L2 (10uH) and L3 (15nH), in series off the DCC pin B3, could you perhaps recommend...
Hi
I am using nRF9160DK SLM application to evaluate the MQTT AT command function.
Everything is fine if the MQTT message is the string type shown by the doc.
But when...
