Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi!
I've just received a nRF9160 DK.
I've installed nRF Connect v2.6.2 and LTE Link Monitor.
I select the device (3 serial ports are shown). I press reset button and...
When working with a custom board with nRF52840 chip, I'm having serious problems with SWD connectivity. In many cases JLinkExe can't connect to target at all. I did some measurements...
Hi there!
I'm trying to simulate a peripheral with a PCA10040 and nRF Connect for Desktop.
I've made the Server Setup, applied to the board and started advertising - everything...
Hello,
I am using nRF52840, SDK_16.0.0, SoftDevice S140 V7.0.1 and Segger for flashing the image. I am using ‘ble_app_blinky’.
Initially I was in assumption that once...
Hi,
Is there a table / .xls available for ALL nordic parts to date?
I'm trying to find all options with +8 dBm TX Power & WLCSP package. (no need for usb)
Hi, I'm trying to get the nrf_stack_guard and nrf_mpu libraries to catch writes past the end of the stack. My stack is 8kB in size (0x2000E000-0x20010000). This is the log...
Hi,
I'm working on the custom board using nrf52832 chip and have performed the secure bootloader using ble on the custom board.
I have made these changes so far on the...
We want to connect provisioned node to multiple mobile application over same mash network (Note: We are trying to give access to multiple user(using multiple mobile) to connect...
Hello!
This may be the wrong place to ask, but I am in search of a gateway (off the shelf or a reference design), that incorporates 802.15.4 through the nrf52840, cellular...
Hi,
I just have a small question: say I have two models, both with publish timeout intervals configured. After some time, one model's publish timeout handler is called....
Hi to everybody,
I'm developing over nRF5 SDK v. 3.2.0 a Zigbee node in router role. In my network I've four of my nodes plus several commercial led light driver and a coordinator...
Hello!
I am setting up SEGGER on my mac. Completed all the steps in Getting Started Assistant. But in the last step at "Set up a project in SEGGER Embedded Studio" where...
Hi,
I am evaluating a project where I want to run light switch on nrf52840. This is supposed to support mentioned protocols - BLE Mesh, Thread and Zigbee, but NOT concurrently...
I plan to connect an nRF52810 bluetooth output to a Johansen Tech 2450AT07A0100 chip antenna via a Johansen 2450FM07A0029 impedance matching chip. Do you have a BT SIG approved...
