Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hello,
I'am working with a project and want to maximize ble throughput from ble thingy52 to a central device. I have used the ble sniffer with wireshark to see data transfer...
Hi Team,
i am working on serial LTE modem sample project trying to send at commands through serial lte link monitor, found that device is not responding to at commands...
Hi,
Recently I updated nRF Toolbox iOS to 5.0.1.
I'm mainly using this tool for writing application via DFU to nRF51822 board.
I was using .hex files for DFU but I can...
Hi,
I am working on a product based on an nRF52832 (SDK 15.3, Softdevice S112 v6.1).
For security purposes, I would like to restrict the pairing / bonding procedure to...
Hello, guys!
I am using master branch of nRF Connect SDK and want to use UART_1 module of nRF9160 SiP to communicate with external devices.
I used nrf9160_pca10090ns.overlay...
Hello, I am evaluating different printed antenna options for my Nordic design using nRF52 series ICs. The small size of the meandered antenna used in the nRF24LU1 USB dongle...
Hi,
I am on SDK 15.2 and NRF52832. I think that I am quite stupid because I do not succeed to be in Non-scannable non-connectable mode.
I tried few stuffs, change directly...
Hello,
I need to create an acl connection using bd_address and GATT client LE connection mode.
how to create ACL connection?
How to close ACL connection using connection...
Hi I purchased nRF52840-DK board recently. I'm able to connect it to Mac OS Mojave and I see that the LED5 is blinking every second. However none of the LED1-4 are blinking...
Hi...
I am developing a product using nRF52833 . (S113, SDK 16, IAR8)
My board uses a lithium-ion battery and uses usb charging.
My board turns on automatically...
Hello.
I am developing using usbd_ble_uart project.
Development platform : nRF52833-DK, s113, SDK 16.0.0, IAR 8.31.1
I want to add static passkey and bonding in my project...
hi,im use nrf52840 and nrf24lu1p to develop my usb+ble+2.4g product,what i use is:
board:pac10056
sdk:
nrf52840:\nRF5_SDK_16.0.0_98a08e2\examples\proprietary_rf\gzll...
I need to minimize current consumption when using FreeRTOS. I have merged freertos with the ble_app_uart example using SDK 15.3.0. I am getting the average current as 9.162...
Hi
I want to create a new project in SES
So I click 'File - New project'
Then this window appeared
What should I select?
Please explain how to do the settings...
