Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
Hi everyone,
I am looking at the SAADC driver and I am struggling to understand the purpose of the nrf_drv_saadc_buffer_convert(). I have read that this is a non-blocking...
Hi,
I want to maximize the indication data throughput and minimize the latency with 4 connected devices.
Setup:
I’m using a nrf52840 as a ble client (sdk 15.2) that...
Hello, I updated the SDK and related SoftDevice of a project based on nRF52832_xxAA
from: 14.2.0 nRF5 SDK - 5.0.0 SoftDevice S132 (compiled works with #define NRF_SDH_DISPATCH_MODEL...
Hallo,
i am currently working on my thesis and i need to build a broadcasting network, in which each node must be able to trasmit to all other nodes, and at the same time...
I am working on project which is based on nrf9160 Development board.
Where the clock is initialized in example code of thread or GPIO ? Which clock source is used by nrf9160...
Hoping this is a simple fix. I'm new to using GIT and I'd like to setup my nRF 5 SDK projects to work with GIT so I can backup and collaborate with others. I have a few nRF...
Hello
I am interfacing between a SPI Master (microcontroller) with a SPI Slave (nRF52832 based chip) and I get the following output on both ends. The transmission seems...
Hi,
I have run into an issue with nrf52840 on pca10056 v1.0.0 board. The softdevice is SD v6.1.0. It seems to be a hardfault which cause a reset when I tried to call sd_flash_write...
Hello,
I need to read resistive sensors values with SAADC. These sensors going throught multiplexer and amplifier. Infortunaly, the signal going into the SAADC is noisy...
There is a race condition in the SAADC driver when using buffer convert.
I am trying to drive ADC at maximum rate to sample 3 ADC channels, and so I call the following in...
Hello,
after I could not use the nRF9160 DK I bought almost a year ago in Germany due to the missing nb-iot coverage I was very curious about the Thingy91 and I assumed...
Sorry for a noob questions but it is essential at this moment as I have not done any development on NordicSemi chips.
What software and hardware tools I need to develop...
Hi,
I am developing a PC SW that connects to nRF52840 device throw a BLE USB dongle(another nRF52840)
How I can tell from PC that a device is connected\disconnected...
Hi,
I use nRF9160 custom board and my application uses USART, ADC, I2c, SPI, RTC and LTE modem. Currently I am trying to reduce sleep current on IDLE state which is 850...
I am going to use nRF52833 chip with SDK v16.0.0 and SoftDevice s140.
There are couple of questions I would like to clarify:
1. Is AoA/AoD direction finding supported...
