Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
SDK 13, softdevice 132
function fds_register results FDS_SUCCESS
by calling the function fds_init debugger stops, see comment in function below, and i see "unknown...
Hi
I'm a total beginner here and I have the gyroscope sensor LSM6DS3 and I have the nRF52 DK
I want to read the sensor's data via I2C (i.e. using SDA and SCL pins) using...
Hello.
This is becoming a very serious issue for me. When I program the nrf52840 dongle and when I switches on the power, it automatically goes into bootloader mode, means...
I purchased a sparkfun breakout board ( https://learn.sparkfun.com/tutorials/nrf52832-breakout-board-hookup-guide and schematic https://cdn.sparkfun.com/assets/learn_tutorials...
I'm compiling a custom application using the CMake scripts in the nRF mesh SDK. When I debug the application, even though the debugger is working – I can pause execution ...
I am trying to modify the central / peripheral relay example to not use the HRM and RSCS services and to use my own custom service instead.
I am following this tutorial...
Hi
I have the nRF52 Development kit and I can program it using SEGGER Embedded Studio IDE without problems. However, when I try to program it using nrfjprog, the Dk doesn...
Hi to all, I'm developing a new device that should be a multiprotocol: Zigbee (as coordinator) and BLE peripheral (with his own GATT) There is an example for this integration...
I asked a question on here couple of days ago, but I resolved that issue and have stumbled into a more concise and in the right direction. I am using ble_app_uart as my code...
I am using ble_app_uart as my code base. I included FDS.c and FDS.h when I compiled, it presented many config errors. I compared the two config files for the FDS example and...
Hi,
I have some problem about Keil hex output file.
At the end of hex file, there have some line as following image.
In (a) of above image, why "hex file" need to...
Hello again Nordic Pro's,
This is a quick question that I have not been able to find the answer for before buying nRF52840 dongles to replace our nRF51 dongles. We need...
When attempting to initiate GPIOTE pins, I get an NRF_ERROR_NO_MEM on the 5th pin. I saw reference to there being a maximum of 4 high accuracy channels but I am attempting...
Hello.
I want to use the CMSIS configuration wizard.
It is work in the example but not in my project.
From looking at youtube I found what I need to add to tool.xml...
