Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hi,
Attached is Cmake error log from one of the failed builds.
This is a new MBP with freshly installed nRF Connect - following tutorial.
Anyway, I am not able to open...
Hi all,
since new version of IOS nRF Mesh App I can't finish provisioning of my nRF52840 DK with flashed light example client.
When I start provisioning for the device...
Hi,
I am using NRF52832 with SDK 15.3 and SD 132 on our custom board ( VDD 1.96V ). I started with with the ble_app_template example for our application. Upon measuring...
Hi Nordic
I am using saadc example now, my device output voltage range is -4v~4v.
my saadc config:
VDD: 3.3V
Reference: VDD/4
Gain: 1/4
Mode: SINGLE_ENDE
i got...
Hi, I am new to BLE, I am trying to send and receive data over BLE and print them in Uart as well in both devices respectively.
And I downloaded lastest NRF5-SDK, I have...
Could you, please, direct me to any example (if available) how to manage lost bond with nRF52832/ SDK16 BLE?
Let say very common situation that will try to demonstrate with...
Hi all,
I have hardware as below:
nRF52840-DK - as an advertiser and the same type of board nRF52840-DK - as a scanner
My problem is that I want to send more data than...
Hi,
I have been going through the Bluetooth Course ( https://github.com/NordicPlayground/nRF52-Bluetooth-Course ) and I can' seem to make it work, even if copy/paste the...
Hi,
I'm using nRF51822 to develop our products. I found an interesting problem on our PCB. After I disconnected our PCB from central device, the main function starts from...
I am developing a wearable using nRF52832. I am using SKD_15.3 ble_app_uart source code for testing. And use Putty together. This source code implements UART Baudrate up to...
I have been using fds for flash saving and read. I have used fds_record_write(..) with no errors and proper readings on the just before performing a 4th fds_record_write(...
I'm currently investigating nRF Connect SDK. The nRF5 SDK (15.3.0) has a function to notify the advertise scan reception channel, but the current nRF Connect SDK does not...
Hi,
I want to test ble_app_tile project in SDK 16.0.0.
The project needs to install pack NordicSemiconductor.nRF_DeviceFamilyPack.8.27.0 in Keil 5.
However, I did some...
