But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
I have questions about nrfutil's latest.exe. Dose it able to do OTA DFU over BLE for every SDK version's firmware?
I have been trying do OTA DFU using Master Control Panel...
Hello,
I've the nRF51 DK which works fine because I managed to upload BLE Softdevice and application with nRFgo Studio. But I cannot get the MCP (Master Control Panel)...
Hi,
I'am working on a project that use the NRF52832 and i can only use P.23 and P.12 on my custom board because they are already wired to a connector, others pins are not...
What is pinout for nrf51822QFAA ?
Everywhere is description Generals Purpouse and I don't know which pin is I2C or SPI.
I don't want long find in example source codes.
Am Working on android application where the Requirement is User will get a Notification about firmware update having YES or NO options.If the user selects the YES options...
hello,
I want to make a beacon with NRF51822 chip.
But now i have a trouble:
In normal working mode, after i stopped the advertising with sd_ble_gap_adv_stop() ,i cann...
Hi,
I am working on one project.
The background I use now is using SDK14.1 and SDH version 5.0.0-2.
The tool is using Keil.
I wonder if I can use two USB descriptors...
There's a serialization library for the soft device, but it's not clear whether the NFC library can be used via this interface: github.com/.../pc-ble-driver
Hi,
I'm following instructions for testing Thread Secure DFU example and I can't get this working. I think there's a problem with client application. LED3 starts being...
Hi,
I want to change my gzll receivers from NRF51 to NRF52. But I've done some performance testing to see if it is really necessary. And here is my problem:
When using...
Can we update DFU firmware through cloud. without selecting the zip file present in Internal Storage of Phone.
In nrf connect app present in play-store its asking ZIP file...
Hi! I use ICM-20602 motion sensor that is similar to MPU6050. Its communication type is also I2C.
I made I2C wrapping module for ICM-20602. In the module, I added i2c_write_byte...
Hi,
I searched devzone and it looks like the Nordic mesh PB-GATT will be available sometime this year. However I'm wondering if it's possible to use Silab's BLE mesh Android...
Hi,
I am using nrf52832 sdk11.0.0 s132 v2.0.1.
In my code app_timer uses RTC1.I want to use RTC2 for counting 1 minute without disturbing the ongoing functionality....
I'm trying to send a string of bytes from nrf51822 to an android device.
I'm using notification.
There will be potentially thousands of data to be sent from nrf51822...
