Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
I just got a nRF51 and am having trouble getting started with it. I created a very simple program using the mbed compiler and produced a hex file which I now wish to flash...
Hello,
I see that the make files that have been included have provision to remove dead code from the projects to reduce code food print. This is accomplished using the...
HI folks,
I have checked the current consumption while connected on an average to be 325uA (with uC taking 4.5uA) so this mean almost 320uA being consumed by the nrf8001...
I have a general question about the RF frequency tolerance of Nordic devices in general. Is the following calculation correct?
Crystal spec = 16MHz, +/-50ppm tolerance...
Are there any plans to add boundary scan functionality to assist ICT testing? If not, are there any other hooks into the part that can be used to test during ICT?
Hello
I'm using a pstorage_register from pstorage.c to register two application storage blocks in flash memory. But I have situation that first module have 6 blocks of...
Hi,
are the GPIO pins broken out on the nRF51 Dongle configurable and can be used for SPI Slave tests? I have a running system powered by a ARM Cortex 4 (Teensy 3.1) and...
We have an early implementation of the v6 SDK DFU ported to support S310 on a handful of devices in the field and need to update them to a new bootloader and we'd like to...
Hi,
With the validation of the BLE V4.2 specification will Nordic be implementing the new features of the spec and if so do you have any idea of availability and dates. ...
Hardware: NFR51822_QFAAC0
Firmware: S110_7.0_SoftDevice
SDK: NRF518_6.0
Application: ble_app_hrs in NRF51822 S110 Examples
I start a timer to toggle led once per...
Hello Everyone,
I want to start working on nRF51822 development kit for my project. but as mentioned on this site : www.nordicsemi.com/.../nRF51822-Development-Kit
that...
Hello there,
I am using the experimental_ble_app_uart with S110 on nRF51-dk and receiving sensor data via 1MHz SPI every time the timer ticks = 100ms.
Data transfer displayed...
Hey,
I created a custom PCB with the nrf51822 that reads two sensors via TWI and transmits certain data over BLE. I can program the chip, print strings to the terminal...
I am having problems with th Master Control Panel (no response from master emulator). When I search devzone, I see an answer related to this question that says cloed because...