Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
I'm trying to install the toolchain manager on a new work computer and I'm running into issues that I think are related to my work's proxy.
I've tried following the steps...
I am trying to configure the STS4x temperature sensor by Sensirion on I2C on a nRF5340DK, I have setup my the coding exactly how sensirion suggested except few changes such...
Hi,
When I try nrfsdk/zephyr/sample/bluetooth/periodic_adv_conn. I notice that the max subevent data size is about 64bytes. If I send a data size larger, I will get a error...
Hi DevZone,
I have made a custom PCB with the nRF52832. I placed the same coaxial connector that is on the nRF52 DK in my PCB. At this point, I want to test the BLE functionalities...
Hi,
I am unable to build the MQTT over Wi-Fi lesson 4, exercise 1 using the nrf7002dk_nrf5340_cpuapp board configuration, but the same code builds successfully with nrf7002dk_nrf5340_cpuapp_ns...
Greetings all, Does the Direct Test Mode (DTM) app v2.4.1 provided in the NRF Connect for Desktop v5.0.2 package support gain settings for the nRF21540 FEM such as +10, or...
I am working on nrf52840 and I want to control the motor speed so I want to generate the variable frequency PWM for the same. How can I generate the variable frequency PWM...
Hello,
I need to configure second UART for nRF52840 DK. So I would like to know the overlay file for uart2 configuration with exact GPIO pins. Also the .c file to initialize...
I 'm porting code from Zepyr 3 .5 to 3 .7 and am having errors in my ds2484 1 -wire device . It was working fine but now reports an init error unless I add deferred -init...
L.S.,
I'm trying to build an "Arduino" port for the nrf52840 (Seeed board).
When building an example I'm getting the following errors during the link phase:
.\Objects...
Hello,
In my project I have b0, mcuboot and an app. My nRF SDK version is v2.7.0.
My project works fine if I use an absolute address in SB_CONFIG_BOOT_SIGNATURE_KEY_FILE...
Hi,
I am working with the nrf9160 and ncs2.7. Is it possible to programmatically change how pins are defined? For example, on startup 2 pins are for I2C (SCL and SDA) and...
I'm seeing inconsistency in reading the ICCID from the nRF9160 modem with modem _info _string _get (MODEM _INFO _ICCID , mystr ,strlen (mystr ) ) ;. All other modem_info calls...
