I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
Hello community,
I am developing a device that uses the NB-IoT network . I would like to know if the NB-IoT module of the nRF9160 supports SMS . If it does, will it provide...
Dear Ladies and Gentlemen,
We have recently started comparing the BM833 (and the corresponding nordic devkit nrf52840) with an other hardware (ESP32), neither uses amplified...
Hello everyone,
please take a look at my minimal reproducable example, which explains the problem and also includes some example measurements. derteufelqwe/nrf-ble-datarate...
Hi
As mentioned in the datasheet, UARTE can operate up to 1Mhz. Is there any special condition/factor to achieve this?
and how fast can a regular GPIO operate?
Thanks...
Computer : Mac Book Air M2
OS : Sonoma 14.5
Hardware : SEEED XIAO nRF52840 Sense
I am building my software using nRF Connect VSCode Extension, while when I select my...
nRF5340 NCS 2.6.1 nrfjprog 10.18.1
My project is based on coap_client and also uses MCUBOOT.
I can program both cores using VS Code, and I notice it splits merged_domains...
Hi,
I am using a nRF9161-DK to flash and debug an external nRF9160 board connected via the nRF9161-DK DEBUG OUT 10-pin connector.
In VS Code "CONNECTED DEVICES", I can...
Hi, I am currently working with the NRF52832 on a custom board that is working with a timer for a particular sleep interval now I have added an external RTC module, and i...
Using nrf9160 with W5500 Ethernet NCS Version 2.6.1
My normal MQTT connection is working fine, but connecting to aws is being an issue. I am getting mqtt -22 error. I...
Hi. I wrote a firmware on nrf9160(SIAA chip), but it doesn't work. On the hardware side, the circuit is same as that of nrf9160-DK, CTS and RTS is short respectively.
If...
Hi,
We are using two nRF54l15-PDF to communicate as SPI, one is in master mode and one is in slave mode. The master device sends a simple array of bytes, the first one being...
Hello,
I'm currently working on NCS2.6.0 and ANT sdk v1.3.0,
I would like to know is it possible to do BLE scanning(without connection) and ANT+ heart rate searching at...
I'm working on getting a radio test example project built for our custom board that is currently in production in order to perform some FCC testing, but I'm struggling to...
