Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Dear Nordic Team,
I am participating in the Board Designer Competition sponsored by Nordic Semiconductor and Autodesk Fusion 360. My project has been selected for free hardware...
Hi,
I am trying to build a BLE PAwR network jammer for wireless network hardening. I have three nrf52840 transmitting on channels 37,38 and 39, which blocks nodes from joining...
I'd like to update a firmware which is essentially made of 2 parts, say 0x1000-0x8000 is a "read-only" part and 0x8000-0x50000 is a "read-write" part. If I flash this firmware...
Hi Nordic Team,
Is there any way to input 3 audio streams (through I2S ) on nRF5340DK board are there any extra I2S Port available to input one more sinusoidal signal and...
Hi,Team,
I am developing Pawr using nrf54l15-dk.
For the Pawr example I refer to E:\NCS\v2.8.0\zephyr\samples\bluetooth\periodic_adv_rsp and periodic_sync_rsp.
I want...
Hi, I'm following the Academy lessons and just tried to get the Blinky sample to work with a nRF54L15DK. I can see on a serial terminal that the code is running and console...
Running the WiFi scan sample on a Thingy91X or NRF7002DK in SDK 2.8 and 2.9 works for scan_done results but if you change to show raw scans, no raw scans are displayed. The...
Hi Support Team
The VDD of customer’s nRF54L15 board is 3V, but the high voltage of P1.10 is about 1V. Did you meet this issue before? Customer needs the output high voltage...
Dear Nordic Team,
I am currently working on a project that integrates your HTTPS client sample with your BLE provisioning sample, specifically on the nRF5340 with the 7002EK...
Hi,
I am testing the Bluetooth remote discovery of the nRF52840 in LE Coded mode with the transmission power set to 8 dBm.
The farthest distance currently achievable is...
Hello, I have developed a module using 54L15 and am currently measuring its RF performance. On Rohde & Schwarz instruments, I have observed numerous test results regarding...
Hi guys, I am using the SDK v2.9.0 and the toolchains b620d30767. To add the build configuration for the sample peripheral_uart, the console print some error log.The log as...
Hello.
I am trying to follow Downgrade protection using MCUboot to enable Hardware-based downgrade protection. However, an error occurred, and the software did not start...
I used the battery routine to test the ADC, and the voltage measured was 3 times larger.
How to fix this problem？
Bat+ is 3.3 V.
dts setting:
vbatt {
compatible...
Hello,
I'm looking for an existing Android/iOS Flutter DFU library that supports nRF5340.
I found this one: https://pub.dev/packages/nordic_dfu but with limitations to...
