Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hi all,
I am working on a project with the nrf52832 and I am using softdevice S132 6.1.1. After creating my desired flash layout (with some help on this forum, thanks!)...
Dear,
I am using NRF52840 and nRF5_SDK_17.0.0_9d13099 and SES development tool.
And also, I am testing SPI master with p0.29/30,31 and P0.26.
but when I do "nrf_drv_spi_init...
I am tring to DFU by Bluetooth with example, but it not work.
Please someone help me!!
My environment
PCA10056 nRF52840
SDK17.0.0
examples/dfu/secure_bootloader...
I was working with the Thingy:91 trying to get into into a serial printing state. I tried to updated the modem and firmware using the nrf Programmer. When updating the modem...
I've been having problems trying to get any of your example project to use NLOG to a uart port that we have made available for production test on our new product.
I've chosen...
Hi,
I am desperately trying to read some RTT Input with Zephyr, but I just cant get it to work!
All I want is to read the RTT Input. I tried with the console and the shell...
Hello,
I am looking at the nrf52840-dongle to explore Bluetooth audio (in headset mode).
So - just to double check:
(1)
I assume I can interface to bluetooth audio...
I'm using nRF52832 + SDK17.0.0 + s132_7.0.1. I am testing buttonless DFU on the PCA10040 board based on this blog, The initial DFU (when there is no app) is successful:
...
Hi, 1) I want to run the client-mesh from DK sources into Dongle. So, I did: - modified the client-dk project: nrf5_SDK_for_Mesh_v4.0.0_src\examples\light_switch_dongle\client...
Hi,
We have been working with a coordinator and a router device based on nRF52840 with nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b
Both devices are Zigbee 3.0 and implement...
Hi Support-Team,
My iOS app crashed when I updated IOS-DFU-Library from V4.6.0 to V4.8.0.
I attached the Xcode debug info and iPhone Analytics.
Thank you very much!
Hello,
Would appreciate some understanding of a compiler warning. Developing for nRF52832 using SDK 15.3.0 plus S112.
This code compiles without warning:
Then I switch...
I have tried a lot of different settings but the NRF52810 still does not output carrier..
How do I configure the radio to only send carrier for NRF52810?
