Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
I have my Thingy:91 working now but I can only see "terminal" data in nRF Connect for Cloud. I was expecting to see graphs of the data and a map when I have a GPS fix. The...
Hello everyone,
I am using light_switch server and client example from nrfmesh examples but nrfmesh ios application cant find nrf52 usb dongle.
I have changed pca10059...
I have developed USB firmware for the 840 based on the USBD example so that we can use WINUSB (WCID) for the host. The design is for USB 2.0 full speed with EPIN1 for device...
ble_nus_data_send() can not work . SDK15.3.0. I have used two NRF52832. Based on the examples ble_app_gatts_c and ble_app_gatts,I have added nus service . Now central role...
Somehow my account got deleted and so did my ticket. I had to re-register my account an i'm creating this ticket again:
nrf9160_pca10090ns.dts.pre.tmp:89.42-101.3: Warning...
Your served radio tramsmitter/receiver example using PCA 10000 USB dongle, PCA 10001 evaluation kit.
It's just only one byte data communication. It works well.
If I communication...
Hi, i'm trying to read an i2c sensor on interrupt. Doing it directly in the interrupt is apparantly bad, so io tried using app_sched_event_put, but that just crashes inside...
Hi,
I'm debugging a small app that is using the LPCOMP to trigger an interrupt when the BLE device is turned off. We have a capacitor to maintain alive the nRF for a while...
Hello,
I am trying to use the nRF9160 DK to publish some sensor data to an Azure IoT Hub. I have been able to successfully connect to the mqtt broker and publish simple...
I am trying to write a custom bootloader to do FW updates on our device. In our main application, we already have a way to transfer a new signed application image over BLE...
Based on nRF52832 datasheet description of DIRCLR register (section 20.3.7), I would expect that writing 1 to bit 8 of that register would set PIN8 (P0.08) to an input pin...
I have two PCA10031 dongles and both seem to be bricked. When I search your web site, I keep finding posts that state that I need to transfer nRF5x-OB-JLink-IF.bin to my device...
I am using SDK_15.3.0. I am using Segger Embedded Studio 4.5.2. I'v tried 4.1.2 also. Every time I compile, even just with an example central project, I get the following...
I updated a working project based on nRF52832_xxAA 32Mhz crystal, from nRF5 SDK 14.2.0 to nRF5 SDK 16.0.0 now the timer is 6 times faster, the code hasn't changed is there...
