But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
I have an external clock running at 3Mhz which I'd like to align with in software. Consider this contrived example:
What would the consequences be of attempting to read...
Hi,
I'm very new to c programming and your hardware. Please excuse my novice questions.
I'm making a rotary braille display using nRF52840 dongle (PCA10059) as it's brain...
Hi,
I using custom nrf52840 board .I have loaded the Bluetooth program in to the custom board using swdio/swclk/vtg/gnddetect these lines.There is no problem in Bluetooth...
I'm attempting to get MMD set up in an IAR project following this tutorial: https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/monitor-mode-debugging---revolutionize...
Dear sir, We are using BL654PA from Laird technologies. We want to check RSSI at 2402MHz, 2440Mhz, 2480Mhz. Can you guide us how to enable PA without using Nordic stack file...
Hello,
I'm using a Thread Border Router built using a Raspberry Pi 3 and a nRF52840 Dongle. I followed the steps at this link: https://infocenter.nordicsemi.com/index.jsp...
Dear Nordic Semiconductor support team
Hi, I got your support using micro:bit with nrf52832 by RADIO in the past as follows.
https://devzone.nordicsemi.com/f/nordic...
I've noticed that Thingy:91 USB code has some issues related to proper handling attach/detach events resulting in incorrect response to usb host requests. Windows device manager...
Hello,
I am using the this sample;
https://github.com/Rallare/fw-nrfconnect-nrf/tree/nrf9160_samples/samples/nrf9160/udp_gps
I want pvt data instead of nmea data...
Hi,
What is the best way to read the async data received on a UART in to a buffer when ever there is an a byte available and in a separate task read the data from the buffer...
I need to include RTOS support in my NRF52840-based system. In order to obtain a good FreeRTOSConfig.h I've looked at the four examples in NRF5 that include FreeRTOS and,...
Hi,
I'm trying to make connection between nRF52840 dongle programmed with "examples/peripheral/cli" application and Windows 10 UWP "CustomSerialDeviceAccess" example code...
Hello
Currently I use the example "ble_thread_dyn_mtd_coap_cli_pca10056" and I would like that my application can detect timeout of the messages sent on the Thread network...
Hello, First of all, I hope you are doing okay about the corona virus crisis. I wish that you stay healthy and safe . Recently, I have been trying to configure ble_app_uart...
Hi Sir,
In the datasheet (V1.1), the table-145 shows the dimensions of WLCSP, but there is no tolerance of D/E/D2/E2
Could you help to advice what is the tolerance of...
