Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
Hi there,
I'm trying to use serial library from SDK to interact with cellular modem (AT commands, not nRF9160). I've read documentation (library description, api). May be...
I have build and flashed the zephire/sample/bluetooth/hci_uart on nrf52840 board and connected the board with ubuntu but hci interface was not created when checked using hciconfig...
Hi,
We have chose LCD which has only 3-Wire support CS, CLK and DI so we have connected that pins with nRF51822 chipset. Now Please see the below image which shows that...
Hi All,
I want to read/write long characteristic (200 bytes max) from Android to my device.
I'm working on the 15.2.0 SDK and S140 Softdevice.
I read some Q&A on...
Hi there,
Right now I am doing some dry research into long range Coded PHY for S=8 or S=2 since I need to have some extra room in the link budget to go the distance. The...
Hi, I'm trying to adapt the ble_gateway example for nRF91dk to use a nRF52 instead a Thingy52. When I change the UUID at ble.c from Thingy to nRF52, I'm not able to get a...
Hello guys,
In next few months I've to put down a new design for a medical product. Both nRF52840 and nRF5340 would fit well the application requirements. But I think this...
I want to use two UARTS ie uart0 and uart1. I read that nrf51822 gpio pins can be set as rx & tx but i couldnt find any example.
I am using SDK12.3
Please attach some...
Hi,
I've looked around the DevZone for answers to this, and haven't quite seen an answer, so I'm going to post my solutions here.
I am using the secure bootloader from...
Hello
I have a use case of typical 3 key (lock / unlock / alarm) car remote lock key fob implementation. Since I already have nRF82810 / 840 based hardware designs that...
I was checking DFU through serial usb/uart on the following link:
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fsdk_nrf5_v16.0.0%2Fsdk_app_serial_dfu_bootloader.html...
I am using nordic nrf52 chip and nordic Soft Device. I observed that power level increases(ramps up ) before finally disconnecting. This behavior is observed when external...
Hello,
I'm working on nRF52832 and i'm porting the SDK15.3.0 (i was currently working with SDK14.2.0) but i'm facing something strange with the function : "ble_stack_init...
hi ... i am using nRF52832 , SDK 15.2 version, using ble_app_uart example , here i want to advertise the device constantly, for that what should i change
i tried to change...
