But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
If I were to design a product using nRF52840 & Thread. Normally, I would have to certify the product with the thread group and become a member. The thing is: - the product...
Hello,
I am developing a remote device which uses system off mode for idle state. I also have the condition where extra long press of any key that is beyond the long press...
My Peripheral is using the ble_conn_params module. I'm seeing that if my Peripheral calls sd_ble_gap_disconnect() soon after making a connection, the module will sometimes...
To the kind attention of Nordic support team,
I'm studying documentation in https://developer.nordicsemi.com/nRF5_SDK/nRF51_SDK_v5.x.x/doc/5.2.0/html/a00140.html where it...
Recently I check back again into att_mtu_throughput example in SDK 15.2. there seems to have some updates than in previous SDK, and I see this BLE_GATT_EVT_DATA_LENGTH is...
Dear all,
I am using the following peripherals in our product.
1. TWI Sensor
2. BLE
3. APP timer (1. to poll a gpio pin & as RTC)
4. SPI flash
5. 2 Edge sensitive...
Hi,
I am using nrf_queue to store data in queue which is inserted with time based interrupt at several milliseconds. Also same data from queue is fetched at bulk.
I am...
Hi,
I have modify a BLE program from ble_app_uart by using SDK 15.3, but the system will crash when I do following test:
Please find attach file for my code.
Step1...
I want to double check current draw in the nRF9160 low power modes and need some help in making sure I know how to do so.
I plan to use an oscilloscope for measuring current...
I hear that the GPS should now work with the onboard antenna of the nRF9160 DK for versions 0.8.5 and later. I also read that the asset_tracker application has been updated...
Hi All,
I'm referring to generic on/off ble mesh example code and we are in the development stage.
I would like to know which pins are used for PA and LNA in the example...
HI
In our application we are using "app_sched_event_put" function but its showing [NRF_ERROR_NO_MEM] when i debugged it please look the screen shot.
The sdk we are...
Hi:
for "ble_app_hids_mouse" example ,it has SWIFT_PAIR_SUPPORTED.
Does HID_keyboard also have this feature?
Could I move swift_pair from "mouse example" to "keyboard...
Hi,
I have an ADC which is interfaced with the nrf52.
The samples from the ADC are collected every 2ms (500Hz sampling rate). I store these samples, and when the number...
