I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Dear Team,
I have a problem with one sensor on some boards, the behavior is not clearly reproducible. On some boards, the "device_get_binding("CCS811")" just delivers exit...
Section 18.6.2 of the nRF52832 datasheet (Power-On reset) specifies the following:
A step increase in supply voltage of 300 mV or more, with rise time of 300 ms...
Hello,
I have tried the GPS sample and it worked fine. Now I want to understand the code more in detail und maybe modify the GPS settings.
But I can’t find any documentation...
Hello NRF Team,
Is it possible to change the I2S buffer size on the fly while a i2s transfer is running ? (I Am using nRf52840 with SDK15.2)
I found in the documentation...
Hi, I am evaluating the nrf52832 and the Softdevice for potential use in a new product. The product has neither display nor keyboard. It therefore makes sense to use Just...
Hello,
I am quite new to developing with the nRF52840-DK. Up to this point, I have been flashing the applications (mostly the examples) over USB with the built-in J-Link...
We need to connect 2 peripherals with single central device.I have taken ble_app_multilink_central from SDK 15.3 and integrated the ble_app_uart_c in this. I am using the...
Hello,
I want to establish an UART communication with rn2483 module with nrf52-DK, SDK 15.2.0
On nrf52-DK, pins 6 and 8 are reserved for serial port, which are connected...
Hello
I used to do TWI communication until now, but it was decided to do sensor reading with SPI communication by changing the sensor.
So that's a question,
What is...
Hello,
I am wondering that when BLE5.1 SDK will be available ?
Is there any possible ways to test your BLE direction finding solution ?
As far as I know, development...
I want to set a keep alive value of MQTT while eDRX is enabled, but it doesn't work well. Any advice?
Environment - hardware: nRF9160 DK 0.8.2 - firmware: 0.7.0-29.alpha...
Hi,
I am using nRF52832 SOC along with SDK v15.2.0 with custom hardware, currently I have requirement to use DFU protocol in BLE application to get a FW of another sub system...
Hello, I hope your day is full of the scent of flowers.
I am in the process of the Ble_Cnetral and PrePhereal project.
I have added and built the Uart.
Why is...
Hi frnds,
I am using the ble_central and ble_peripheral code (nrf52840).
i am sending 400 bytes of data to central from peripheral continuously, sometimes the boards get...
