But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hey there,
I am trying to develop with the Bluetooth Mesh SDK for NRF5.
We have two chips, NRF52840 and NRF52840/NRF52832and are using the light_switch example from the...
I need to save energy for my ble application. So I turned off the sensor when there was no ble connection. A ble connection is a condition for me to turn on the sensor, but...
How exactly are the UART pins selected for the nRF9160? I've searched and am unable to find a file to configure pins. I need to change to pins from the development board to...
Hi,
I'm working with the SAADC on an NRF52832. I'm using the SAADC driver from SDK15.2.
I have a problem with the calibration routine because it's generating DONE events...
Hello,
I am developing an application on the 52840 and so far find the SDK documentation quite confusing and somewhat contradictory. I need to write a simple TWI (I2c) master...
Hi, I’m located in Liège, BELGIUM.
Using the nRF9160DK, an orange SIM card, MODEM firmware mfw_nrf9160_0.7.0-15.alpha I managed to make run some sample code:
mqtt_simple...
Hi. I'm using nRF52832, SDK13.0.0.
The roll is peripheral.
And I'm using Oberon to use ECDH.
I think you have the result or document for random generator's performance...
The nRF9160 DK I'm working on does not seem to be able to connect to nRF Cloud after following the tutorial:
https://www.nordicsemi.com/Software-and-Tools/Development-Kits...
Apologies, I accidentally closed and opened my previous ticket: https://devzone.nordicsemi.com/f/nordic-q-a/53073/unable-to-add-lte-device-on-nrf-cloud , can I check that...
The new SDK has no documentation on this functionality: https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v12.0.0%2Fgroup__ble__radio__notification...
Where to get this RaspPi_OT_Border_Router_Demo_v3.1.0-1.alpha.img file.
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.thread_zigbee.v2.0.0%2Findex...
Hello
I need urgent help. From days I have been stuck exploring NRF SDK 15.0 to do a simple task.
I am using an NRF DK board PCA10040. After going through peripheral drivers...
Hi,
I am working with central and peripheral uart example and facing with connection problem between two boards.After debugging at the central side i am getting error in...
Dear Sir/Madam,
We have a customer to develop a product based on nRF51422 and then they passed their product for pre-registration test.
They used DTM interface to connect...
Hello
I have nRF52832 custom board and have BME280 sensor connected to I2C/TWI
Whatever I do I get same reading (for 3 different sensors)
I'm constantly reading same...
