Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hi,
Recently, I was trying to established an application based on ble_app_hrs with PCA10028.
The MCU I used is nRF51822_xxac (256KB), S130 for softdevice and the SDK is...
After I add uart function to ble_example, I use app_uart_put() to send data,but data only one byte.What can I do?My board is nRF52-DK.SDK is nRF5_SDK_11.0.0_89a8197.This is...
Hi Team,
Iam working on nordic nRF52832 eval boards and trying to send a string from client to server over Bluetooth mesh using sdk v3.2.0.
i have created simple message...
Hi,
I am trying to increase the through put of the BLE peripheral device.
SDK Version-15.3, NRF52832 chip set
I looked into the example code ble_app_att_mtu_throughput_pca10040_s132...
Hi,
I am looking for support driving a Piezo bender for a car Alarm system. These alarms generally make multiple alarm sounds in a periodic changing manner. I am trying...
Dear All.
I'm using nRF52840 DK, 15.3.0 SoftDevice, Segger.
I'm testing DFU and have some question. and i'm begginer with all
I'm so s orry in advance.
First...
I have the nRF5 Mesh SDK "beaconing" demo compiled and running on my nRF52-DK. Is there a way to setup the beacon to be an iBeacon, so that it broadcasts a UUID, Major, Minor...
Hi,
I wrote a firmware using softdevice. How can i upload softdevice and firmware i wrote using nrfjprog command line tool. Also is it possible to locking firmware to prevent...
after update nRF Connect from 3.0.0 to 3.2.0 I started to get the error :
nRF52840 Unsupported device. The detected device could not be recognized as neither JLink device...
This is for the SDK nRF5_SDK_15.2.0_9412b96 and custom hardware.
I have a bootloader based off the example secure_bootloader_usb_mbr_pca10056 project. I want the application...
I'm using an nRF52832 with s132 and nRF5 SDK v15.2.0. I have a question about the tutorial devzone.nordicsemi.com/.../radio-notification The input parameter radio_evt of SWI1_IRQHandler...
Hi,
I have a customer interested in using the NRF9160 with a 1000mA/h battery.
They want to keep the board sleeping for 15 minutes, wake up and send GPS data position...
Hi,
Zephyr 2.1.0 will be released 2019-11-29, and it will support LwM2M Queue Mode which is an important feature for sleepy devices, see https://github.com/zephyrproject...
I am trying to modify the asset_tracker application to work without PSM mode since we cannot get PSM mode granted from the local network here.
My plan is to switch the modem...
