But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello everybody, I am trying to exercise the DFU for mesh following the DFU quick start guide (v2.0.1). To put you in context I have four nRF52840 devkits, three of them are...
hi..
i am using nf52832 ... segger 15.2version ... while i am start to execute the code .. i am getting the error at nrf_breakpoint_cond ... then i tried to set breakpoints...
Hi,
I am new to software development and had a query about software version control with the Keil IDE using git.
As a beginner, I simply copied an example project in the...
Hello,
I'm on nrf52DK PCA10040, SDK15.2
I'm sure it's quite basic, but I don't get it. I just need to write actually two uint32_t value in flash memory (so FLASH_DATA_LENGHT...
Hi,
I have got a nRF542840 dongle, and I have installed all the required programs (I got all from this website: https://www.nordicsemi.com/eng/Products/Getting-started-with...
I recently went through the process of building the pc-ble-driver-py library/drivers and running it on my NRF528240 Dongle and have no issues with it. I wanted to share it...
Hello,
I have problems to get SES working with nrf51822 projects. If i import project with help of tutorial from nordic semi i get undefined symbol __data_start__. Now i...
Good day!
Work with nrf51822 central with S130,
I've read this questions and links in answers:
https://devzone.nordicsemi.com/f/nordic-q-a/20924/sd_ble_gattc_char_value_by_uuid_read...
My application is based on one of the example projects and runs on the nRF DK. Next step is to port this application to a custom board. Are there any guides written on this...
below is a little part of code I copy from nrf5_SDK_for_Mesh_v2.2.0_src:
***********************************************************************************************...
Hi
I need a CLI over RTT on an existing project. I believe that I have extracted all the required bits from the CLI example. I dont need history, UART, USB or anything else...
I am using NRF52832, twi_sensor_pca10040 example with SHT3X sensor.
I changed slave address to 0X44 and SCL, SDA pin to 27 and 26. TWI TX transfer work fine, in response...
using nRF-Sniffer-v2 at 52832 sniffer, I can get advertising packet. When select device form drop-down list, & connect the device the sniffer can't get any packet. Any one...
