But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hi
I am porting another nRF52840 SPI OLED driver based on nRF5_SDK_14.2.0_17b948a\examples\peripheral\spi_master_using_nrf_spi_mngr
At first, it works fine without button...
hi guys ;
i have already an application on android phone that can read and write charchtéristic i also followed the tutorial Bluetooth low energy Characteristics, a beginner...
Hello
I am using nrf51822 .The function of DFU has worked well,but some weird problems puzzle me.
1、After DFU is successful,what is nrf51822's working state? Does it reset...
When I just plug the USB cable on the board I get a GPIO high voltage of 3V. But when I also put +5V on the external supply pins, the GPIO high voltages are 4.5 V. Is this...
Hi,
We are using nrf52832 board with sdk14.0. We are facing two issues:
Our use case is to send the data continuously when the notification is enable and stop...
The Bluetooth pairing is not working properly. I am developing the Application based on Bluetooth pairing with UART. Here I have included my concept and Program.Help me out...
Hi to everyone!
I have been getting the output of NRF_LOG_INFO functions through RTT in J-Link RTT Viewer terminal. The code has been executing in nRF52832DK.
Now I...
I have set up an nrf cloud and can control the led on pca10056 using the nrfcloud so configuring the gpio(pin no 7(Port P0.7))is becoming a problem.Can u provide me with a...
Hello,
I bought a nordic/wellcore ibeacon (nrf51822) to experiment. I want to enable all the features and would like to know what value to assign to the temparature enable...
Hello, i am using SDK12.2.0 and SD s130 on a nRF51822 (AC) and i am trying to add an external interrupt on a pin in the cscs ble_peripheral example. The code i am using (and...
Hi
We are using sdk version 12.2.0 and trying to change it to sdk 14.0.0. However, when I measured the power while converting the code, ppk confirmed that the sdk 14.0...
Hi all,
I'm using SD S132 v5.0.0 with SDK 14.0.
I'm testing now the BL buttonless DFU (and later the SD buttonless DFU) after working well with the app buttonless DFU...
I've implemented monitor mode debugging as described here and it works great. When I get a hard fault, it doesn't break in the IDE anymore. So it appears to be running fine...
I can connect the kit to the nrf cloud and even add the device to the gateway but i cannot switch on and off the leds.Where is the source code for the nrfcloud example?I cannot...
