Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
Hi everyone, maybe I'm wrong but I think that the Garmin oregon 600 uses a ANT+/BLE chip made by NordiSemi, it's possible to know exactly which one it is?
Thank you a lot...
Hello,
i'm trying to DFU from 13.1 to 14.1..
What i have tested is flash(SD + B) + dfu(APP) on both versions. Now i'm trying to DFU all from sdk13.1 to 14.1.
Is it...
I know that latest nRF5 SDK and nRF mesh SDK support SES, it's really a good news for developer. I'm just curious that, can I use SES to flash SoftDevice on macOS? If so,...
Hi;
I am using NRF52 DK(pca10040) board nowadays with sdk 14.0. I read a blog post about power consumption in nordic webpage.( link )
In this blog post, there is a webpage...
I´m currently developing ble peripheral application for the nRF52832 with SDK v13.0.0. I need to have a secure connection between the nrf and android or ios mobile device...
Hi There,
i am new to nrf51822 and new to program this kind of controller.I searched over the website, I couldn't find a good introductory documentation for programming the...
hello there,
i am using nrf51422 but dont know how to write a program for uart. i want to send AT commands to Quectel M95 using uart .
good help appriciated!!
cheers...
Hi. I'm using nRF51822.
My solution needs power on and off continuously.
I think that is not so good at chip.
Do you have any data for how many times it can bear for PWR...
Hi, I'm using nrf52810.
Size of flash memory of nrf52810 is 192kb according to the datasheet.
But size of hex of S112, nrf52810 softdevice, is 281kb.
Why size of S112...
Thanks for reading my question.
I use SDK14 , PCA10040, S132 and modified a little bit of uarte driver, but that should not affect what I said below.
I set the DMA buffer...
I read about Segger studio (on their website) that it reduces the code size. I try to check it out
Here's my opposite result
I've compiled the same app (e.g uart_example...
Hi all , when I run and debug my code , I frequently encounter error :
I think it's related RAM configuration on KeilC .
Please show me what is error ? And how to solve...
Hi there,
So I'm going through that complicated step of setting up the IDE for the first time to get started programming and I'm having issues doing it with the SES and...
hi everyone ,I want to ask you a question, I use the SDK12.3, when the device from the application transformation to the bootloader, when DFU is failed, why the deice is stays...
I am using nRF51822 (PTR5518A) with SDK v12 and s130 softdevice. To dump the code I am using nRF52 DK segger (PCA10036). With that I am able to dump the code but there is...
