This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Where can I get a copy of the nRF52 Reference Manual?
The nRF51 Reference Manual is here:
www.nordicsemi.com/.../nRF51_Series_Reference_manual v3.0.pdf
Where can I...
i am programming nrf-51 dk's program.
i have to get data from sensor, so i am studying example code which is twi_sensor.
i don't know well these function.
nrf_drv_twi_tx...
[hide preview]
.
I am looking for a detailed description of the Memory Protection Unit for the nRF51822 as described at a high level in nRF51822_PS v3.1.pdf.
I know...
Dears,
I have tried the example code of PWM function at nRF52 DK(PCA10040).
It worked with a 2V DC level. Is there any mistakes or something wrong? Why a DC level...
I use the SDK v11.0 alpha, the S130 with my USB-dongle(NRF51422).
I use the low_power_pwm to initialize 4 different PWMs. I used the Example low_power_pwm_s130_pca10031...
Hi,
I have a problem with pwm,
I am using keil uvision 5.17, SDK 9.0.0, SD 130, nRF 51822.
I have programmed the code which can control servo motor(SG90) by smartphone...
I'v read the Arduino SDK for nRF8001 (and Poring ACI to any other microcontroller)
some questions:
1)the source code is complicated and there is'nt enough comment on that...
Not sure if forums or MyPage support requests are better for this.
It seems NRF_LOG has taken a step backward from what was used in the previous nRF52 0.9.2 SDK. What I...
hello there . i want to get i2c data on ble advertising packet
int main(void)
{
uint32_t err_code;
bool erase_bonds;
ret_code_t ret_code;
int16_t x_val;
int16_t...
Hi, I have PCA10036 board v1.0.0 and I would like to run sample projects from nRF5_IoT_SDK_v0.9.x that are by default designed for PCA10040. Do I need to make any changes...
hi. I want to work with nRF8001 by STM32F103 family from ST.( www.st.com/.../LN1565) is there any one who develop a project with STM32F103 by using STM32CubeF1 ( www.st.com...
hi,
i am using nrf51822 s110 sdv 7.1.0,when i upgrade the soft device, application and boot loader(create .zip) using the nRF toolbox application. application shows me...
