Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
We evaluated the BLE Mesh DFU performance on the nRF52840 and observed that transferring a 342 KB binary took approximately 36 minutes. This aligns closely with the documentation...
Hello!
Can you map the zephyr versions to the LTS versions if possible?
We are using NCS 3.02 with the zephyr version 4.0.99. How does this relate to any of the LTS...
Hello.
I am developing in the following environment. ・nrf52832 custom board ・nRF5 SDK v17.1.0
This program already supports BLE communication, BLE DFU functionality, AD...
Hello.
During production, we occasionally encounter products that exceed the reception sensitivity standards.
Of course, we only select those that completely exceed...
I need to use PPI on my custom nRF52840 board, which selects soc nRF52840 as per copying nrf52840dk. However, this doesn't enable "HAS_NRFX", which is hard to track how that...
Hi,
I'm running the location sample on nrf9151dk from v3.0.0 of nrf-sdk. Hardware details:
I have these additional configs added to my prj.conf
This is the output...
I am working on a custom Cluster Definition Using Matter Cluster Editor 0.1.0 I have created a couple of structures on the structure tab and they are not being saved to the...
I am designing a wearable device that uses BLE and UART. During the development stage, I worked with the nRF52 Development Kit and started with the ble_app_uart example from...
Hi,
What would be the best way to alter pin's functionality from UART TX ->RX->GPOUT ->GPIN in runtime? (NCS2.5/Zephyr nRF52840)
Is it supported by Zephyr/devicetree...
Hi. I can't build the hello_dect example using cmake, the build process is failed with the following error: In file included from /home/cybermag/ncs/nrf/modules/trusted-firmware...
Hi,
In this post Hung Bui states that there can only be "maximum 4 pin events, each for one GPIO pin (so max 4 pins at a time)". This is (apperently) not true since I...
While scanning for devices with NCS 2.9.2 my device suddenly stops sending adv reports after a few hours.
It seems like this might have been fixed in a recent version...
BOARD: nrf54l15 DK
SDK: 3.1.0
Hi,
I am trying to setup my low power preipheral with a new ble address via bt_id_create.
Everthing works fine when I use the exact...
Hello! I am developing an application for the nRF5340, and I am using split cores, so the controller is on the network core and the application is on the other core. I want...
Hello Nordic Support Team,
I’m working with an nRF5340 on nRF Connect SDK 3.0.2 , using both the Distance Measurement (DM) service and BLE DFU.
My application topology...
