Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi all,
Currently we are trying to measure the power of nRF52832 using (1) nRF52 DK board, (2) power profiler kit 2 (PPK2).
We used PPK2 in source-meter mode and we connected...
Shalom!
I have a custom nRF9160 board with uart0 connected to the outside world by RS232. I set the uart0 as the printk() debug output. I also need to write and read binary...
I get that is has to do with something around the MSB. But I cant seem to find a way to prevent this. No i can not send a byte 0x00 since this will trigger certaint behavior...
Hi,
I am developing an Openthread application using Nordic Connect SDK for the nrf52840dongle. I updated my nrf SDK to bd075cc09. Since then, my application won't boot anymore...
Hi,
I need to switch DK to 3v as my custom board has 3v.
When I switch VDD_IO to 3v board doesn't start at all. LED5 blinks for a moment but nothing happens.
Switching...
Hi,
I am currently working on an internal dfu modeled after the secure_bootloader_uart/ example in SDK 15.3.0. I have gotten the dfu to perform a successful dfu with the...
Hi!
I am developing on a custom board and only have the Debug in connector P3 from nrf9160dk to debug the board. I want to send AT commands to configure the modem and will...
I am a systems engineer helping my team in the component selection phase of the project that involves BLE communication between our master side and a simple remote control...
I have issue to program nrf52832 with nrfjprog command line.
my program use nrf52formesh sdk. I developed with Segger Embedded Studio with GCC on the Linux PC. I modified...
Hello all,
I have successfully installed nRF Connect, nRF Connect SDK v1.6.0 and SEGGER Embedded Studio (SES) v5.50.c to run and debug some samples on my nRF5340 Development...
Hello everyone,
I CAN NOT include the ocrypto_ecdsa_p256_public_key.h file into my project.
What are configurations I need to enable?
I'm new to NCS, could you provide...
Hi, Nordic
This is the test result that I use nRF52833 as the host to connect the slave, slave txpower = 0dbm.
And use Wireshart Sniffer to grab the air packet when...
Hi.
I recently started work on some projects where I have to use I2c OLED and BLE. I used OLED to display time which is running on an internal RTC of nrf52832.
Now I merge...
Hello sir,
i am using nrf52832 board and i am getting following error when i build the code are as follows:
1..\_build\nrf52832_xxaa.axf: Error: L6218E: Undefined symbol...
