Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
Hi Great Nordic Support Teams:
Our client is developing their BLE products with 5340 , and they'd like to use NCS SDK 1.4.0.
They setting up the NCS environment with...
Hello. I have a issue about fstorage.
first, I using S332 SD and SDK 15.3.0 version and 52832.
Init flow is below:
Log enable -> SD enable -> SD BLE & ANT enable ->...
Hi,
SES is not including the extra cmake build options, i tried prefixing "--" as we do it in west build, note that it works west build "west build -b nrf9160_pca10090ns...
I am attempting to create a custom Buttonless DFU application by building on top of the default example from the SDK. Specifically, I am merging the Buttonless DFU app with...
Hello,
I am new to the BLE world. I have a nrf52 DK and using softdevice 7.0.1
I am trying to to flash the basic blinky example.
In debug mode everything is fine,...
Hi, I have a custom board with an nrf52840 onboard I was able to program the nrf52, but then I executed:
% nrfjprog --eraseall
and,
% nrfjprog --pinreset
and the JLink...
According to the Zephyr documentation here the way to implement an application-specific exception handler is to define k_sys_fatal_error_handler. When I try to do this I get...
Hi. I'm doing the firmware on the custom board.
This board turns on when the button is pressed through the power button circuit. And I created the reset function using NVIC_SystemReset...
Hello, I would like to develop a simple program that sends and receives UART communication through 2 boards.
The example used "examples\peripheral\serial\pca10056\blank...
Hi, all
I'm using nrf52832 pca10040, s132..
I want to send and receive data over Tx , Rx pin.. with my custom board, cm1106 model..
<<<<<< I've connected the two devices...
Not something which I have experienced, but rather inferred from reading the code of nRF5_SDK_17.0.2_d674dde/nRF5_SDK_17.0.2_d674dde/components/libraries/log/src/nrf_log_frontend...
HI, I'm creating an IoT system, and planning to use THREAD to communicate between devices. Each device is running on a raspberry pi but I plan to use nRF52840DKs to do all...
Hi,
I am seeing a bricked device due to the fds_init() returning FDS_ERR_NO_PAGES. After some debugging, I found that all pages are marked as FDS_PAGE_DATA (no FDS_PAGE_SWAP...
Hello everybody
I hit another issue with sd_ble_gap_disconnect.
The short story is this one. I want the peripheral to initiate a disconnect if no activity for a predefined...
