Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi, With this setup in , I successfully built a CIS mode using my nRF5340 DKs , enabling stereo sound while the microphone is active .
However, I am currently experiencing...
I am currentry trying to evaluate the RAYTAC-MDBT50Q-CX-40.
Raytac Corporation 勁達國際電子股份有限公司
But sample applications(helloworld, blinky) don't work.
I installed the...
Hi,
I was working on Channel Sounding for my NRF54L15 boards and suddenly the boards in "connected devices" were no longer visible. I don't know how it happened and what...
Hello,
Im trying to security connecting but i'm getting this bug.
After auth_passkey_display(), Next step is so late(more then 3min).
Tool : VS code
SDK : nRF...
Using VSCode and the nRF Connect VSCode extension, each time a debug session is started the target is erased and programmed, regardless of whether the code was changed.
...
Dear Nordic TS,
I'm trying to power an nRF9161 DK with a simple external battery. According to the documentation, I thought that this battery voltage should be applied between...
Hi community,
I need to get data from the BMI270 sensor that is on the Thingy:53 board. I have already taken some previous topics as reference but I still haven't been successful...
Knowing, that the AS-RAI implementation is experimental, I would still prefer to have more documentation about the details.
I already asked for these details in an other...
I am working through BTLE Fundamentals, Lesson 6, Exercise 2, and running the code from blefund_less3_exer2 per the instructions and it all looks good on the app COM log:...
i'm already able to TX and RX arbitrary packets between my own bare-metal test programs running on a pair of DKs... since both programs used identical configurations (mode...
Hello! I am currently developing my own custom service with two nrf 52840 development kits where one acts as the Client and one acts as the Server. I have managed to set up...
Dear devzone，
Based on ncs2.9.1 and nRF54L-DK(v0.9.2), add in the prj.conf of the peripheral_uart example:
Compile and burn to nRF54L15-DK, the program does not run, and...
Wheh I try to debug a multi-domain-image on an nrf5340 or 52840, I can debug the mcuboot domain just fine. But when I try to debug the app-domain (I tried this with the zephyr...
Hi,
Using Visual Studio Code, when I build asset_tracker_v2 in NCS v2.9.1, for nrf9160dk/nrf9160.ns, I keep getting the problem shown in the subject line
equivalently...
Dear Team,
I have a question regarding preventing LTE from endlessly searching for a network connection. Lately I have been facing issues where LTE connection is rejected...
